Petroleum, synthetic, and natural waxes have been used as hydrophobic bases for dispersions intended for use as barrier coatings for packaging paper. Oil-in-water dispersions with alkaline pH were prepared by a two-step homogenization procedure containing paraffin wax, with various characteristics, the Fischer–Tropsch synthesis product or beeswax. The size of the dispersed particles determined by dynamic light scattering depended on the type of hydrophobic base used and was in the range of 350–440 nm. The ability of dispersion particles in aggregation driven by electrostatic attraction, evaluated by Zeta potential analysis by electrophoretic light scattering, was from −26 to −50 mV. Static multiply light scattering was used for 30 days of stability assessment and helped to select the dispersion with a Sarawax SX70 wax base as the most stable. Dispersions were further used for coating the backing of kraft paper by the Meyer rod method. Coated paper with an applied coating of 6 g/m2 had very good hydrophobic properties (Cobb60 < 4 g/m2), sufficient strength properties, and air permeation, which enabled its application as a packaging material. The dispersions based on Sarawax SX70 wax were evaluated as the best coating for Mondi ProVantage Kraftliner 125 g/m2 backing paper. Good hydrophobic properties and strength properties indicate the possibility of using the SX70-based wax dispersion coating as a replacement for PFAS coatings in some applications.
19 September 2022 in Materials Chemistry and Physics
The lubricating properties of the lubricants were tested under boundary friction conditions; it was found that the surface-active additives had reduced the wear mark and thus the value of the Goz/40 parameter (limiting load of wear). The introduction of a surfactant containing amide compounds into the oils and greases was highly effective in slowing down the oxidation process. Lubricants containing mono–15 ([3-(N,N,N-dimethylbuthylamine)propyl]hexadecanamide chloride) and 15–4–15 (tetramethylene-bis [3-(N,N,N-dimethylamine)propyl]hexadecanamide) additives were characterised by higher oxidation stability compared to the unmodified lubricants. Both of the analysed substances showed bactericidal properties against Staphylococcus aureus and Salmonella enteritica. Tests of antibacterial activity in the lubricants with the addition of mono–15 and 15–4–15 confirmed that these lubricants can be considered bactericidal against Gram-positive and Gram-negative bacteria.
The lubricating properties of three secondary amides were evaluated using the four-ball apparatus method. It was found that the studied amides—N-propylpropanamide (AC3C3), N-propyloctanamide (AC3C8), and N-propyldodecanamide (AC3C12)—could be a promising group of new AW/EP (anti-wear/extreme-pressure) additives for lubricants, especially for silica-thickened greases. Of the amides tested, AC3C8 was found to have the best properties. The synthesized amide structures were immobilized on SBA-15 nanosilica and examined as described above. Notably, SBA-15 has not previously been reported as a potential lubricant additive. The results of the tribological tests showed that SBA-15-immobilized amides performed better than non-immobilized amides. Nevertheless, the lack of stability of the amide-grafted SBA-15 when dispersed in oil limits its use in targeted formulations and should be improved through further research. By testing a silica-thickened grease, a synergistic effect was observed between the free-amide AC3C8 and a commercially available additive containing butylated triphenyl phosphate. A 240% increase in the Goz40 parameter (anti-wear properties) and a 150% increase in welding load (extreme-pressure properties) were obtained with the addition of 2%w/w of commercial additive and 3%w/w of AC3C8 to a base oil.
Przedstawiono zastosowanie nanocząstek krzemionki, w szczególności jako dodatków do środków smarowych. W doniesieniach literaturowych przeważa ich zastosowanie jako nośników katalizatorów i napełniaczy polimerów. Jednym z nowych, rozwijających się obszarów zastosowania nanocząstek krzemionki są dodatki do środków smarowych, w których pełnią one funkcje m.in. zagęszczaczy i dodatków przeciwzużyciowych. Przedstawiono potencjalne korzyści ze stosowania nanocząstek krzemionki jako dodatków do środków smarowych, poparte publikowanymi w literaturze wynikami badań trybologicznych. Przedstawiono najważniejsze wyzwania związane z otrzymywaniem dyspersji zawierających nanocząstki krzemionki, z których najważniejsze są: przeciwdziałanie utracie stabilności oraz określenie wpływu funkcjonalizacji krzemionki na właściwości dyspersji.