Konstantin Igorevich Makarenko

Dr. Konstantin Igorevich Makarenko

Center for Materials Technologies, Skolkovo Institute of Science and Technology, Skolkovo, Russia
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 October 2022 in Materials & Design
Verified
Journal Article
Open access
Konstantin Igorevich MakarenkoKonstantin Igorevich Makarenko
Konstantin Igorevich Makarenko
SKStepan D. Konev
Stepan D. Konev
ODOleg Dubinin
Oleg Dubinin
ISIghor Szyszkowsky
Ighor Szyszkowsky

11 December 2020 in Materials
Verified
Journal Article
Open access
PDF file
Konstantin Igorevich MakarenkoKonstantin Igorevich Makarenko
Konstantin Igorevich Makarenko
ODOleg Dubinin
Oleg Dubinin
ISIghor Szyszkowsky
Ighor Szyszkowsky
The paper is devoted to the direct energy deposition (DED) of functionally graded materials (FGMs) created from stainless steel and aluminum bronze with 10% content of Al and 1% of Fe. The results of the microstructure analysis using scanning electronic microscopy (SEM) demonstrate the existence of a dendritic structure in the specimens. The crystallization rate of the gradient binary Cu-Fe system structures was investigated and calculated using the model of a fast-moving concentrated source with an ellipsoid crystallization front. The width of the secondary elements of the dendrites in the crystallized slab was numerically estimated as 0.2 nm at the center point of the circle heat spot, and the two types of dendrites were predicted in the specimen: the dendrites from 0.2 to approximately 50 nm and from approximately 0.1 to 0.3 μm in width of the secondary elements. The results were found to be in good accordance with the measured experimental values of the dendritic structure geometry parameters.

22 February 2023 in Metals
Verified
Journal Article
Open access
PDF file
Konstantin Igorevich MakarenkoKonstantin Igorevich Makarenko
Konstantin Igorevich Makarenko
ODOleg Dubinin
Oleg Dubinin
ISIghor Szyszkowsky
Ighor Szyszkowsky
The coefficient of linear thermal expansion and the specific heat capacity of laser-deposited Cu-Fe alloys fabricated from tin, aluminum, chromium bronze (89–99 wt.% Cu), and SS 316L were studied. The investigated alloys had a 1:1 and a 3:1 bronze–steel ratio. The Al–bronze-based alloy showed the lowest value of linear thermal expansion coefficient: (1.212 ± 0.095)∙10−5 K−1. Contrarily, this value was the highest {[(1.878–1.959) ± 0.095]∙10−5 K−1} in the case of functionally graded parts created from alternating layers of bronze and steel. Differential scanning calorimetry provided experimental results about the specific heat capacity of the materials. In the case of Al–bronze-based specimens, it demonstrated a decrease in the specific heat capacity until ~260 °C and its further increase during a heating cycle. Exothermic peaks related to polymorphic transformations were observed in the Al–bronze-based specimens. Cooling cycles showed monotonous behavior for specific heat capacities. It had exothermic peaks in the case of Cr–bronze-based alloys. A Lennard-Jones potential equation was used for testing the relation between heat capacity and thermal expansion. A three-way interaction regression model validated the results and provided the relative thermal expansion of commercially pure DED-fabricated SS 316L. Its specific heat capacity was also studied experimentally and was 15–20% higher in comparison to the traditional method of production.

1 November 2020 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
Konstantin Igorevich MakarenkoKonstantin Igorevich Makarenko
Konstantin Igorevich Makarenko
ISIghor Szyszkowsky
Ighor Szyszkowsky
The paper demonstrates the results of microstructure, microhardness and elasticity analysis of the functionally graded (FG) specimens with multilayer structure created of stainless steel and aluminium bronze powder materials via direct energy deposition (DED) laser technology. Increase of microhardness (up to 266 HV) and Young’s modulus of elasticity (up to 43.2 GPa) along with growth of the dendritic crystals in the gradient structures are observed. The results of numerical simulation demonstrate stress distribution in FG Cu-Fe system structure with a sharp interface. The results of the research can be used for 3D-printing of the aerospace industry details created from two kinds of material with rather different thermomechanical properties.

20 July 2022
Verified
Book Chapter
Open access
PDF file
Konstantin Igorevich MakarenkoKonstantin Igorevich Makarenko
Konstantin Igorevich Makarenko
ODOleg Dubinin
Oleg Dubinin
ISIgor V. Shishkovsky
Igor V. Shishkovsky
Direct energy deposition is a reliable additive manufacturing method of producing components with highly sophisticated geometry from a single material or combination of different materials with high manufacturing freedom and efficiency. The assembly operations are not required after the direct energy deposition: such complex parts as a rocket combustion chamber, a nuclear reactor element, a heat exchanger, and so on, could be fabricated layer-by-layer during one technological step. Promising applications are associated with Cu-Fe system laser deposited functionally graded components, which allow combining good oxidation resistivity, antifrictionality, thermal, and electrical conductivity of copper with mechanical strength, processability, and corrosion resistance of stainless steel. The main issue, which appears in the case of laser deposition of such materials, is internal stresses caused by significant inequality of physical properties of copper/bronze and steel, their limited miscibility, forming of brittle phases at the interface, and complexity of variation of mechanical and physical properties of the resulted alloy. The mentioned factors could cause various cracking in resulted parts. Specific techniques such as ultrasonic assistance, implementation of the external magnetic field, and post-treatment (hot isostatic pressing, machining), could be suggested to improve the quality of laser deposited Cu-Fe system functionally graded materials.

1 January 2024 in Russian Journal of Nondestructive Testing
Verified
Journal Article
Closed access
PDF file
MMM. M. Murashev
M. M. Murashev
VEVyacheslav Em
Vyacheslav Em
VGV. P. Glazkov
V. P. Glazkov
ISIghor Szyszkowsky
Ighor Szyszkowsky
Konstantin Igorevich MakarenkoKonstantin Igorevich Makarenko
Konstantin Igorevich Makarenko
ESElena А. Sulyanova
Elena А. Sulyanova
The paper presents the results of studies of additively manufactured metal samples using neutron imaging at the IR-8 research reactor of the National Research Center “Kurchatov Institute” (NRC KI). The advantages and disadvantages of neutron imaging using monochromatic (DRAGON station) and polychromatic (PONY tomograph) neutrons when studying internal structure of the samples are demonstrated.