Lais Alves

Prof. Lais Alves

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 January 2018 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Open access
PDF file
MAMarcio Moreira Arouche
Marcio Moreira Arouche
SBS. Budhe
S. Budhe
Lais AlvesLais Alves
Lais Alves
SFSofia Teixeira de Freitas
Sofia Teixeira de Freitas
Mariana Doina BaneaMariana Doina Banea
Mariana Doina Banea
Silvio De BarrosSilvio De Barros
Silvio De Barros
In this work, an experimental study has been carried out to evaluate the effect of salt water condition on the long-term adhesion of composite-to-metal bonded joints using peel tests. A new test configuration is tested via fully and partially immersed specimens with 500 mm length. Fracture surfaces of non-aged samples exhibited a cohesive failure within the adhesive layer, which indicates a good adhesion of the joint. Results revealed a significant difference in the interface adhesion between aged and non-aged condition after 150 days of immersion. Partially immersed specimens allow to evaluate the adhesion performance of the joint under dry and wet condition in single specimen using a simple peel test.

3 July 2021 in Journal of Asian Ceramic Societies
Verified
Journal Article
Open access
Lais AlvesLais Alves
Lais Alves
NLNordine Leklou
Nordine Leklou
FSFabio de Souza
Fabio de Souza
Silvio De BarrosSilvio De Barros
Silvio De Barros
Fibers can increase the ductility of geopolymer materials, acting as reinforcements to improve mechanical properties. These improvements depend on fiber content and quantity. This study evaluates the impacts of different percentages of glass fiber on a GBFS (ground blast furnace slag) geopolymer matrix. The glass fibers were used on the critical length of 20 mm, obtained by pull-out test in previous studies. Percentages of 0.25%, 0.50%, 0.75%, and 1.00% of glass fiber in mass were tested in fresh state, by flow measurement, and in hardened state, by variation of shrinkage, water porosity and response of composites under flexural and compressive load conditions at 7, 14, 28, and 90 days. The mixture resulted in a high porosity geopolymer paste. In addition, an analysis of variance (ANOVA) was performed to evaluate the statistical significance of fibers in compressive strength. The results show that increasing percentages glass fibers, until 0.75%, enhances mechanical properties. Percentage of 1.00% started to show accumulation of branch of multifilament fibers which contribute to higher drying shrinkage. The ANOVA test showed that the percentage of fibers can influence the compressive strength. With the results, the optimum percentage of fibers for his composite mixture was found at 0.75%.

14 October 2020 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
Lais AlvesLais Alves
Lais Alves
NLNordine Leklou
Nordine Leklou
Silvio De BarrosSilvio De Barros
Silvio De Barros
Concrete is a major construction material that produces high levels of carbon dioxide in its manufacturing process. Hence the construction sector is responsible for relevant environmental impacts. This justifies the need to find materials as green and ecological alternatives to common Portland cement. Geopolymers represent the most promising alternative due to its proven durability, mechanical and thermal properties. This study investigates the effects of solid-to-liquid and alkali activator ratios on the synthesis of slag-based pure geopolymer and their relation to the geopolymerization process. Two activating solutions were used: a) a mixture of sodium hydroxide, sodium silicate, and water; and b) a mixture of potassium hydroxide solution, potassium silicate, and water. As precursor material, ground blast furnace slag was used. Precursors and activators were mixed with solid-to-liquid ratios in range of 1.5 to 2.2. In the first stage of the study, the mechanical properties were evaluated for each activating solution. In the following stage, different formulations, with variations in the water percentage and solid-to-liquid ratio were tested for mechanical properties and SEM observations. Test results indicate that the resulting geopolymer has the potential for high compressive strength and is directly affected by the composition of the activating solution. It can also be observed that compressive strength was affected by solid-to-liquid ratio and % of water added to the mixture, and strength increased with ageing day.

31 January 2013 in International Journal of Sustainable Development and Planning
Verified
Journal Article
Closed access
EVE. Vazquez
E. Vazquez
SRS. Rola
S. Rola
DMD. Martins
D. Martins
Lais AlvesLais Alves
Lais Alves
MFM. Freitas
M. Freitas
LRL. Pinguelli Rosa
L. Pinguelli Rosa

22 September 2025 in Materials
Verified
Journal Article
Open access
PDF file
Lais AlvesLais Alves
Lais Alves
Nordine LeklouNordine Leklou
Nordine Leklou
FSFabio Simone-Souza
Fabio Simone-Souza
Silvio De BarrosSilvio De Barros
Silvio De Barros
Ground granulated blast furnace slag (GBFS)-based geopolymers represent a viable binder system that combines mechanical efficiency with a significantly lower carbon footprint when compared to conventional Portland cement. This work examines how thermal curing between 20 °C and 80 °C affects setting time, mechanical performance, shrinkage, and porosity of GBFS-based geopolymers. Curing at 40 °C accelerated gel formation, yielding compressive strengths up to 71.9 MPa. This regime also reduced shrinkage and porosity. In contrast, curing at ≥60 °C caused structural degradation and reduced long-term performance. Statistical analysis (ANOVA and Tukey post hoc) confirmed significant effects of curing regime and age on performance. These findings provide key insights for optimizing thermal curing of slag-based geopolymers, supporting their deployment in environmentally responsible construction practices.

16 January 2021 in Journal of Adhesion Science and Technology
Verified
Journal Article
Closed access
Lais AlvesLais Alves
Lais Alves
NLNordine Leklou
Nordine Leklou
PCPascal Casari
Pascal Casari
Silvio De BarrosSilvio De Barros
Silvio De Barros
The reinforcement efficiency on a composite depends on the effective transfer of the stress between matrix and fiber. This work presents an experimental and comparative study of fiber-matrix bond strength for fiber-matrix interface between glass fibers and carbon fibers added to the slag-based geopolymer matrix. This analysis was performed by pull-out test. A total of 18 tests have been conducted, three for each type of fiber at each embedded length of 10 mm, 20 mm and 30 mm. The critical embedded length and the maximum interfacial shear (bond) strength were analyzed, and SEM observations were carried out for the cross-section of each fiber to measure diameter and observe the interface. It was found that the greatest efficiency was obtained by reinforcing with the glass fibers, incorporated at 20 mm in the slag-based matrix.