A mechanical heart valve (MHV) is an effective device to cure heart disease, which has the advantage of long life and high reliability. Due to the hemodynamic characteristics of blood, mechanical heart valves can lead to potential complications such as hemolysis, which have damage to the blood elements and thrombosis. In this paper, flowing features of the blood in the valve are analyzed and the cavitation mechanism in bileaflet mechanical heart valve (BMHV) is studied. Results show that the water hammer effect and the high-speed leakage flow effect are the primary causes of the cavitation in the valve. Compared with the high-speed leakage flow effect, the water hammer has a greater effect on the cavitation strength. The valve goes through four kinds of working condition within one heart beating period, including, fully opening stage, closing stage and fully closing stage. These four stages, respectively, make up 8.5%, 16.1%, 4.7% and 70.7% of the total period. The cavitation occurs on the fully closing stage. When the valve is in closing stage, the high pressure downstream of the valve lasts for about 20 ms and the high-speed leakage flow lasts for about 200 ms. This study systematically analyzes the causes of cavitation emerged in the process of periodic motion, which proposes the method for characterizing the intensity of the cavitation, and can be referred to for the cavitation suppression of the BHMV and similar valves.
1 March 2022 in Nuclear Engineering and Technology
A high-temperature and high-pressure valve is the key equipment of a wind tunnel system; it controls the generation of high-temperature and high-pressure g
With the rapid development of industries, hard sealing ball valves are increasingly adopted in extreme working conditions, especially for the advantage of high sealing performance. However, current research works on ball valves are lack of leakage rate prediction, which is an important issue. In this paper, a typical hard sealing ball valve is selected as the research object. Mathematical equations for sealing pressure are derived on both fixed and floating ball valves. The sealing pressure on the hard sealing side of the ball valve is analyzed, and the accuracy of the theoretical equation is verified. Meanwhile, the relationship between sealing performance factor and sealing pressure is fitted, and a prediction method of hard sealing ball valve is proposed, and also is validated experimentally. Results indicate that the sealing pressure obtained from the theoretical equation is conservative, as the actual pressure on the sealing surface exhibits a U-shaped distribution. The sealing performance factor varies with sealing pressure according to a piecewise function. It increases in the form of a power function when the pressure is less than 110 MPa and decreases in the form of a quadratic function when the pressure is higher than 110 MPa. The R2 of the fitting equation is greater than 0.98%. Furthermore, the theoretical predictions are consistent with the experimental results in magnitude, confirming the reliability of the proposed prediction method. When the roughness is below 0.2, further reduction in the roughness has little effect on the sealing performance. Both roughness and sealing pressure should be considered comprehensively to enhance sealing performance. This work can benefit the leakage rate prediction and further study for the sealing performance improvement of hard sealing ball valves.
Dry gas seals (DGSs) are currently the preferred sealing method for high-speed rotating machinery, widely used in the fields of petrochemicals and energy and power. This study analyzes the effect of groove structure and operating parameters (rotary ring speed and inlet pressure) on the performance of the sealing system. The results show that a swallowtail-like groove demonstrates a dual effect of improving film stability and reducing leakage under specific working conditions. Specifically, under the inlet pressure of 4.5852 MPa and rotational speed of 10,380 rpm, the swallowtail-like groove achieves a 1.84% reduction in leakage and a 0.32% increase in opening force compared with a conventional spiral groove. Rotational speed has the greatest impact on the gas film stability of the cluster spiral groove. Increasing inlet pressure enhances the dynamic stabilization of gas film. Dynamic analysis indicates that the opening force demonstrates a linear proportionality with inlet pressure, whereas leakage follows an exponential growth. This work can provide guidance for optimizing the groove structure in dry gas sealing systems.
About Me
Advanced flow control and sealing technology for smart control valve
Advanced flow control and sealing technology for smart control valve