Nitrogen-doped indium tin zinc oxide (ITZO:N) thin film transistors (TFTs) were deposited on SiO 2 (200 nm)/p-Si〈1 0 0〉 substrates by RF magnetron sputtering at room temperature. The structural, chemical compositions, surface morphology, optical and electrical properties as a function of the active layer thickness were investigated. As the active layer thickness increases, Zn content decreases and In content increases gradually. Meanwhile, Sn content is almost unchanged. When the thickness of the active layer is more than 45 nm, the ITZO:N films become crystallized and present a crystal orientation along InN(0 0 2) plan. No matter what the thickness is, ITZO:N films always display a high transmittance above 80% in the visible region. Their optical band gaps fluctuate between 3.4 eV and 3.62 eV. Due to the dominance of low interface trap density and high carrier concentration, ITZO:N TFT shows enhanced electrical properties as the active layer thickness is 35 nm. Its field-effect mobility, on/off radio and sub-threshold swing are 17.53 cm 2 V −1 · s −1 , 10 6 and 0.36 V/dec, respectively. These results indicate that the suitable thickness of the active layer can enhance the quality of ITZO:N films and decrease the defects density of ITZO:N TFT. Thus, the properties of ITZO:N TFT can be optimized by adjusting the thickness of the active layer.
In-Sn-Zn oxide (ITZO) thin films have been studied as a potential material in flat panel displays due to their high carrier concentration and high mobility. In the current work, ITZO thin films were deposited on glass substrates by high-power impulse magnetron sputtering (HiPIMS) at room temperature. The influence of the sputtering power on the microstructures and electrical performance of ITZO thin films was investigated. The results show that ITZO thin films prepared by HiPIMS were dense and smooth. There were slight variations in the composition of ITZO thin films deposited at different sputtering powers. With the sputtering power increasing from 100 W to 400 W, the film’s crystallinity was enhanced. When the sputtering power was 400 W, an In2O3 (104) plane could be detected. Films with optimal electrical properties were produced at a sputtering power of 300 W, a carrier mobility of 31.25 cm2·V−1·s−1, a carrier concentration of 9.11 × 1018 cm−3, and a resistivity of 2.19 × 10−4 Ω·m.
In this study, the homojunction thin-film transistors (TFTs) with amorphous indium gallium zinc oxide (a-IGZO) as active channel layers and source/drain electrodes were fabricated by RF magnetron sputtering. The effect of oxygen partial pressure on the phase, microstructure, optical and electrical properties of IGZO thin films was investigated. The results showed that amorphous IGZO thin films always exhibit a high transmittance above 90% and wide band gaps of around 3.9 eV. The resistivity increases as the IGZO thin films are deposited at a higher oxygen partial pressure due to the depletion of oxygen vacancies. In addition, the electrical behaviors in homojunction IGZO TFTs were analyzed. When the active channel layers were deposited with an oxygen partial pressure of 1.96%, the homojunction IGZO TFTs exhibited optimal transfer and output characteristics with a field-effect mobility of 13.68 cm2 V−1 s−1. Its sub-threshold swing, threshold voltage and on/off ratio are 0.6 V/decade, 0.61 V and 107, respectively.
N-doped InSnZnO (ITZO:N) thin films as the active layer of thin film transistors (TFTs) were prepared using radio frequency (RF) magnetron sputtering at room temperature.
In-Sn-Zn oxide (ITZO) nanocomposite films have been investigated extensively as a potential material in thin-film transistors due to their good electrical properties. In this work, ITZO thin films were deposited on glass substrates by high-power impulse magnetron sputtering (HiPIMS) at room temperature. The influence of the duty cycle (pulse off-time) on the microstructures and electrical performance of the films was investigated. The results showed that ITZO thin films prepared by HiPIMS were dense and smooth compared to thin films prepared by direct-current magnetron sputtering (DCMS). With the pulse off-time increasing from 0 μs (DCMS) to 2000 μs, the films’ crystallinity enhanced. When the pulse off-time was longer than 1000 μs, In2O3 structure could be detected in the films. The films’ electrical resistivity reduced as the pulse off-time extended. Most notably, the optimal resistivity of as low as 4.07 × 10−3 Ω·cm could be achieved when the pulse off-time was 2000 μs. Its corresponding carrier mobility and carrier concentration were 12.88 cm2V−1s−1 and 1.25 × 1020 cm−3, respectively.
One-dimensional ZnO nanowires offer significant potential for optoelectronic applications, though their controlled synthesis remains challenging. This study optimized ZnO nanowire growth via carbothermal reduction vapor transport based on the vapor–liquid–solid mechanism. Key parameters investigated were gold catalyst thickness and annealing, source temperature, system pressure, and oxygen concentration. Results show that thinner Au films promote high-density, small-diameter nanowires. An optimal source temperature window (950–1000 °C) was identified, while pressure and oxygen content critically influenced growth mode by modulating vapor supersaturation. Under optimized conditions, aligned single-crystalline ZnO nanowires with hexagonal wurtzite structure were achieved. Structural and optical characterization confirmed high crystallinity and strong near-band-edge emission, demonstrating the efficacy of the developed approach for tailored nanowire synthesis.