In recent years, the idea of the operation of energy systems (power systems, heating systems) has changed significantly. This paper is an overview of locally balanced energy systems without the use of fossil fuels. The paper justifies the concept of local energy balancing in a new energy system that does not use fossil fuels (coal, natural gas, and crude oil), based on European Union guidelines and formal documents as well as the literature on the subject. In this context, the issue of local energy self-sufficiency, utilizing renewable energy sources, as well as the concept of local smart grids based on innovative market mechanisms are raised. Attention is also paid to technical issues with regard to locally balanced energy systems, in particular photovoltaic sources and energy storage. Challenges related to the use of electrical protection in networks with many sources of energy are described. In such networks, the power flow is not in one direction only. Moreover, the selection of protections is problematic due to the distribution of short-circuit currents. Additionally, earth fault currents in such networks may be distorted, and this negatively affects the operation of residual current devices. The basic nomenclature describing locally balanced systems has been sorted out as well. Finally, possible future research paths in the field of creating locally balanced systems without the use of fossil fuels are presented.
Currently, electric vehicles are a rapidly growing alternative to those with combustion engines and can contribute to reduction of CO2 emissions in the transport sector, especially when the energy to power electric motors is predominantly derived from renewable sources. Until now, the comparison of environmental impact and influence of electric transport means on the power systems was not fully addressed in the case of Poland. The purpose of the study is to describe, analyse and assess electric vehicles (EV) operation against performance indicators in Poland, especially the influence of electric transport means (ETM) (electric cars, trams, trolley buses and buses) on power system and environment. The influence on the power system was investigated for the Polish National Powers system using the simulation of different scenarios of loads generated by EV charging. The energy demand of the National Power System and daily load variability indices were determined. Based on the data of ETM powers consumption and emissions of energy production, the emissions of harmful gases per one km and per one person were calculated, as well as the financial outlays for energy necessary to drive 1 km per 1 passenger. To assess and compare the environmental impact of the selected ETM life cycle, the life cycle assessment method was used. The results of environmental impacts were determined for selected assessment methods: CML 2 and IPCC 2013 GWP 100. The functional unit in this study is one selected ETM with a service life of 100,000 km. Comparison of trams, trolley buses, buses and electric passenger cars indicates that most beneficial are electric buses which do not need rails or overhead lines, thus investment costs are lower.
Currently, in rural networks with a large amount of distributed generation, PV installations are often disconnected due to the excessively high voltage in the network, which often exceeds the limit value, in accordance with the PN-EN 50160 standard. Disconnecting such an installation extends the return on investment costs by preventing the generation of electricity for the owner’s needs and results in the consumption of this energy from the grid. In such a case, the recipient has to bear the costs related to the purchase of this energy. In order to solve the problem of excessively high voltage in a low-voltage distribution network with a large amount of distributed generation, the authors of this article proposed a new approach to the use of electricity from these sources. In order to present the benefits of the proposed solution, a computer simulation was used. In order to carry it out, a mathematical model of a low-voltage power grid with distributed generation was developed using the electric multipole method and Newton’s method, which is discussed in the paper. To determine the advantages of the proposed solution, nine variants of the operation of an exemplary low-voltage power grid over one day were analyzed. The main conclusion based on the analysis of the results is that the proposed approach improves the operation of the power system by maintaining the voltage values within the standard range for the entire tested part of the network. In addition, the proposed approach does not increase the power or electricity when generating electricity from a PV installation. The proposed solution can also serve as a very attractive stimulus for the creation of energy cooperatives.
The development of power electronics, including high-efficiency power supply systems, changes the structure of perception of the types of electrical energy receivers connected to the power grid at each supply voltage level. In the past, the dominant type of receivers were constant impedance devices. Currently, more and more devices have power supplies, which are most often constant power receivers. The construction and technological diversity of receivers allows mixed receivers, which are a combination of constant power and constant impedance receivers, to be distinguished. Therefore, there is a need to determine the impact of the type of electrical energy receivers on the power grid, both in the context of the operation of a single receiver and in the case of a branched power grid with a high penetration of distributed generation. This article will discuss the impact of the type of electrical energy receivers on the operation of the power grid, with particular emphasis on the issue of electrical energy losses at changing voltages. To determine the impact of receivers, simulation studies were performed based on two case stages: the first is a fragment of a low-voltage power grid in a household that supplies a heating device, which is analyzed as a different type of receiver; the second is a fragment of a low-voltage power grid with various types of consumers and photovoltaic installations. The research was carried out on the basis of the mathematical model of the low-voltage power network developed by the authors using the electric multipole method and Newton’s method. The obtained results show that the type of receiver may have an impact on electrical energy losses.
Electric vehicles are increasingly appearing on Polish roads due to a number of technical, legal and marketing conditions. However, electromobility is developing primarily in urban areas, mainly due to the unevenly developed infrastructure for charging vehicle batteries and the power grid. Therefore, solutions should be created that use the existing power infrastructure, including the use of railway power infrastructure (RPI). The railway power network covers a significant part of the country, including forest areas, and, above all, it very often intersects with road infrastructure or runs along roads. This paper raises issues related to the possibility of using RPI to charge the batteries of electric vehicles. After characterizing the technical, operational and legal requirements related to these technical systems, a concept of an electric vehicle charging system using RPI was developed, along with a demonstration of the possibility of its implementation, which was simulated using mathematical models developed by the authors.