Different Al–4Cu–1.5Mg/WC composites were synthesized through powder metallurgy to establish the effect of WC particle addition on the abrasive wear behavior of an Al–4Cu–1.5Mg (wt. %) alloy. The wear tests were performed using a pin-on-disc tribometer at room temperature in dry conditions using SiC abrasive sandpaper as a counterbody and tribometer of linear configuration. The results showed that WC additions increase the hardness of the Al–4Cu–1.5Mg alloy due to the strengthening effect of particle dispersion in the aluminum matrix, which generates an improvement in the wear resistance of the composites by preventing direct contact of the sample with the counterbody, in turn delaying the plastic deformation phenomena responsible for the degradation sequence. In addition, the dominant wear mechanism was abrasive wear, and the increased friction coefficient did not bring a rapid wear rate, which was related to the enhanced deformation resistance due to the high hardness.

The current work shows the optimization of the preparation of nanosized titanium carbide in situ through mechanical alloying. Metallic titanium powders, along with two carbon sources, carbon nanotubes, and stearic acid, were used to reduce the particle size (around 11 nm) using an SPEX 800 high-energy mill. The combined use of 2 wt % of these carbon sources and n-heptane as a liquid process control agent proved crucial in generating nanoscale powder composites through a simple and scalable synthesis process within a 4 h timeframe. The uses of 20 wt % of both carbon sources were compared to determine the ability of carbon nanotubes to form carbides and the decomposition of process control agent during mechanical milling. The structure of the composites and starting materials were evaluated through X-ray diffraction and Raman spectroscopy, while the morphology features (average particle size and shape) were monitored via scanning electron microscopy and transmission electron microscopy.

Al–Cu–Mg composites reinforced with sub-micron tungsten carbide (WC) particles were synthesized by powder metallurgy and subjected to T6 heat treatment to clarify the interplay between dispersion strengthening and precipitation hardening. Composites with 1–3 wt.% WC (average size 0.8 μm) were solution-treated at 540 °C for 3 h, water-quenched, and aged at 195 °C for up to 100 h. Microstructural analyses confirmed a uniform distribution of WC and demonstrated that its presence did not modify the dissolution–precipitation sequence of the Al-Cu-Mg matrix. Transmission Electron Microscopy observations provided direct evidence of θ′ (Al₂Cu) precipitates. The 3 wt.% WC composite reached peak hardness after 5 h (78 HRF), a 15% increase over the T6-treated unreinforced alloy, and exhibited a 40% higher yield strength (330 MPa). These improvements were attributed to the combined effects of Orowan strengthening and age-hardening precipitates (θ′). The results demonstrate that integrating powder metallurgy, sub-micron WC reinforcement, and T6 treatment is an effective route to enhance strength in Al–Cu–Mg alloys without delaying aging kinetics.

The current work presents the influence of the magnesiothermic synthesis method on titanium carbide (TiC). In this method, powdered titanium precursors and two carbon sources—turbostratic carbon and carbon nanotubes—were employed in proportions of 10 wt.% and 20 wt.%. The refinement of the X-ray diffraction (XRD) patterns using the Rietveld method for TiC suggests suggested coexistence of two phases, cubic with Fm-3m space group and hexagonal with P3₁21 space group. In particular, for the sample with 20 wt.% of carbon sources, the XRD refinement revealed that the cubic phase accounted for 94% of the composition, in contrast to a secondary hexagonal phase, Ti₆C_3.75, which comprised 6%. The influence of carbon on the morphology (particle size and shape) and crystallite size was monitored through bright-field transmission electron microscopy (BF-TEM) imaging and XRD. In samples containing 20 wt.% carbon, a homogeneous morphology in both size (around 11 microns) and shape was observed, along with a reduction in crystallite size (from 22.7 to 17.8 nm). Raman band analysis further revealed vibrational modes indicating that carbon induced disorder in the TiC structure. The magnesiothermic synthesis method developed in this work offers a low-cost approach of interest in the aerospace and automotive industries. Additionally, the study provides significant insights for particles used as additives or reinforcing agents to enhance the mechanical properties of metal matrix composites (MMCs).

In the present manuscript, the influence of reaction time on the hexagonal-to-monoclinic phase transition in hydroxyapatite (HAp) nanofibers synthesized via a low-temperature modified hydrothermal method at 100 °C is investigated. The resulting nanofibers were highly crystalline and stoichiometric, with a Ca/P ratio of approximately 1.67. Comprehensive structural and functional characterization, combining X-ray diffraction with Rietveld refinement, Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, transmission electron microscopy (TEM), and resonance-tracking piezoresponse force microscopy (RT-PFM), was employed to elucidate the role of the non-centrosymmetric monoclinic P2₁/b phase in governing HAp’s structural and piezoelectric properties. The analyses indicated a time-dependent phase evolution from hexagonal (P6₃/m) to monoclinic (P2₁/b), with exclusive formation of the hexagonal phase at 6 h and a clearly dominant monoclinic fraction (73.56%) after 24 h. Nanofibers synthesized for 48 h comprised approximately 98% monoclinic HAp and exhibited elongated morphologies with an average length of 354.82 nm and diameter of 45 nm. RT-PFM measurements confirmed a pronounced piezoelectric response associated with the monoclinic phase, yielding an effective piezoelectric coefficient (d_eff) of 19.85 pm/V. In vitro MTT assays demonstrated that the high monoclinic content did not compromise biocompatibility, as cell viability and cytotoxicity met the requirements of ISO 10993 and ASTM F895 standards. These findings offer new insights into how monoclinic ordering governs the piezoelectric behavior of HAp and suggest a promising strategy for enhancing its performance in biomedical applications.