Mayra Agustina Pantoja Castro

Mayra Agustina Pantoja Castro

División Académica de Ingeniería y Arquitectura, Universidad Juárez Autónoma de Tabasco, Jalpa de Méndez, Tabasco, Mexico
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2021 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
MRManuel Olán Ramos
Manuel Olán Ramos
EMEbelia Del Angel Meraz
Ebelia Del Angel Meraz
JRJosé María Rojo
José María Rojo
Daniella Pacheco-CatalánDaniella Pacheco-Catalán
Daniella Pacheco-Catalán
MCMayra Agustina Pantoja Castro
Mayra Agustina Pantoja Castro
RENE MORA-ORTIZRENE MORA-ORTIZ
RENE MORA-ORTIZ

22 March 2021 in Materials
Verified
Journal Article
Open access
PDF file
RENE MORA-ORTIZRENE MORA-ORTIZ
RENE MORA-ORTIZ
EMEbelia Del Angel Meraz
Ebelia Del Angel Meraz
SDSergio Diaz
Sergio Diaz
FHFrancisco Magaña Hernández
Francisco Magaña Hernández
EMEmmanuel Munguía-Balvanera
Emmanuel Munguía-Balvanera
LQLeobardo Alejandro Quiroga
Leobardo Alejandro Quiroga
In this research we evaluated the use of recycled fine mortar aggregate (RFMA) as a fine aggregate for new masonry mortar creation. The pre-wetting effect on the aggregate before creating the mixture was analyzed as a method to reduce its absorption potential. A control mixture of conventional mortar and two groups of recycled mortars were designed with a partial replacement of natural sand by RFMA (pre-wetted and not pre-wetted) performed in different proportions. The results established that the pre-wetting process allows a reduction in the amount of water required during the creation of new mixtures, regulating the water/cement (W/C) ratio and improving the properties of recycled mortars such as air content, fresh and hardened densities, and compressive and adhesive strength for all substitution levels. Mortar made with a 20% substitution and pre-wetted until it was at 67% of its absorption capacity displayed adhesive values higher than the ones shown by the reference mortar. The pre-wetting process proves to be an easy performance technique; it is inexpensive, environmentally friendly, and the most valuable fact is that specialized equipment is not necessarily needed. This process is the most profitable option for improving RFMA exploitation and reuse.

1 January 2022 in Tecnología y ciencias del agua
Verified
Journal Article
Closed access
EMEbelia Del Angel Meraz
Ebelia Del Angel Meraz
MCMayra Agustina Pantoja Castro
Mayra Agustina Pantoja Castro
RGRosendo López González
Rosendo López González
ACAlida Elizabeth Cruz
Alida Elizabeth Cruz

25 December 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
RENE MORA-ORTIZRENE MORA-ORTIZ
RENE MORA-ORTIZ
EMEbelia Del Angel Meraz
Ebelia Del Angel Meraz
SDSergio Diaz
Sergio Diaz
EMEmmanuel Munguía-Balvanera
Emmanuel Munguía-Balvanera
FHFrancisco Magaña Hernández
Francisco Magaña Hernández
JTJazmín del Rosario Torres-Hernández
Jazmín del Rosario Torres-Hernández
In this research, the use of the pre-wetting technique is proposed as an ecological alternative to reduce water absorption in waste oyster shells used in the production of masonry mortar as a partial substitute for natural sand. An experimental study was conducted to assess the properties in both the fresh and hardened states of masonry mortars. Two mortar groups were prepared based on a control mixture, with natural aggregate replaced by crushed oyster shell (COS) in varying proportions. In one group, the COS was pre-wetted, while in the other group, the COS was used at its natural moisture content. The experimental results demonstrated that the pre-wetting process aided in reducing the water–cement ratio (w/c) in the mortar mixture, thereby improving its properties. In both mortar groups, favorable results were observed with respect to capillary water absorption. Although the compressive strength was affected by the incorporation of COS, pre-wetted mortars with substitutions of up to 30% achieved the reference value established in this research. The pre-wetting process proves to be a straightforward and cost-effective technique; it is environmentally friendly and will contribute to decreasing the accumulation of COS in landfills, thereby safeguarding natural material reserves.

14 November 2024 in Materials
Verified
Journal Article
Open access
PDF file
RENE MORA-ORTIZRENE MORA-ORTIZ
RENE MORA-ORTIZ
EMEbelia Del Angel Meraz
Ebelia Del Angel Meraz
SDSergio Diaz
Sergio Diaz
FHFrancisco Magaña Hernández
Francisco Magaña Hernández
JTJazmín del Rosario Torres-Hernández
Jazmín del Rosario Torres-Hernández
MCMayra Agustina Pantoja Castro
Mayra Agustina Pantoja Castro
This research presents an experimental analysis of the mechanical behavior of masonry mortars incorporating disposable face masks (FMs) cut into two different sizes. The objective is to provide experimental data contributing to the consolidation of recycling FMs in mortar mixtures. To achieve this, two types of mixtures were prepared: one with strips of 3 × 3 mm and another with strips of 3 × 10 mm. These FM strips were added in different proportions by the volume of mortar (0%, 0.2%, 0.5%, 0.8%, 1.0%, and 1.5%). In all mortars, the dry bulk density, volume of permeable voids, and water absorption, as well as compressive, flexural, and tensile strengths, were evaluated after a 28-day water immersion curing period. Additionally, two essential properties in masonry mortars were analyzed: air content and shear bond strength. The results indicated that, for both strip sizes, adding FMs up to 0.2% positively affected the flexural and tensile strengths; concerning control mortar, increases of 6% and 1.4%, were recorded, respectively, for the longer strips. At this percentage, the density, air content, and compressive and shear bond strengths are not significantly affected. The results demonstrated that incorporating FMs into mortar mixtures is a promising avenue for sustainable recycling and helps reduce microplastic environmental contamination.

23 October 2025 in Materials
Verified
Journal Article
Open access
PDF file
RENE MORA-ORTIZRENE MORA-ORTIZ
RENE MORA-ORTIZ
SDSergio Diaz
Sergio Diaz
EMEbelia Del Angel Meraz
Ebelia Del Angel Meraz
FHFrancisco Magaña Hernández
Francisco Magaña Hernández
MCMayra Agustina Pantoja Castro
Mayra Agustina Pantoja Castro
EMEmmanuel Munguía-Balvanera
Emmanuel Munguía-Balvanera
This study presents the development of hybrid masonry mortars by incorporating two waste materials: recycled plastic strips from disposable face masks (FM) as mechanical reinforcement and calcined oyster shell powder (OSP) as a filler. The objective was to evaluate the combined effect of FM and OSP on the mechanical behavior of mortars. Three types of mixes were prepared: a reference mix, a mix with 5% OSP (by cement weight), and mixes with 5% OSP reinforced with FM strips. FM strips were incorporated at three different lengths, dividing the FM-reinforced group into three subgroups (0.1%, 0.2%, 0.5%, and 0.8%). The results showed an approximately 10% increase in compressive strength with the addition of 5% OSP compared to the control mortar, as well as an improvement in bond strength of about 21%. Furthermore, an optimum content of 0.2% of 6 mm strips allowed for adequate dispersion and maintained indirect tensile strengths similar to the control + OSP. OSP acted as a reactive filler, increasing compressive strength and improving both density and adhesion. However, higher FM contents or longer strips increased porosity and water absorption, while reducing strength. This combination represents an innovative strategy for valorizing post-pandemic and marine waste.