The Savonius drag-type wind turbine suffers from poor efficiency due to the adverse negative torques on the returning blades when they rotate against incoming flows. It was proven that using a suitable deflector system has the potential to improve wind turbine efficiency. However, as previously identified in studies, the common drawback of using a flat deflector is the strong wake zone behind it. The present study aims to improve the overall performance of a drag-type wind turbine by using a cylinder deflector with a wake splitter plate to manage and mitigate the detrimental effect of the wake zone behind the deflector. The wake control and suppressing vortex shedding downstream of a circular cylinder have been divided into active and passive flow control techniques. Amid the latter control methods, the adoption of splitter plates has proven to be highly effective for wake control and suppressing vortex shedding behind the cylinder. Unlike previous studies, a cylinder deflector with the wake splitter plate will be utilized instead of the conventional deflectors to improve the efficiency of the wind turbine by disturbing the wake zone downstream of the deflector. To obtain a more efficient configuration, the effect of the variations of the wake splitter length (Ls/D), attachment angle (θwsp), and the count of wake splitters on the outputs such as generated torque coefficient (Cm), power coefficient (CP), and wake zone on the performance of the Savonius rotor were investigated via Computational Fluid Dynamics simulation. The results revealed that cylinder deflectors with the wake splitter increased the Savonius rotor's performance the most for almost all Tip Speed Ratios (TSRs). The average Cm and CP raised considerably up to 15% using a deflector with two wake splitters at TSR = 0.6 compared to the case without deflectors.
This paper proposes a new augmentation device to improve the coefficient of power (Cp) of a Savonius turbine using a Computational Fluid Dynamics (CFD) method. The device is a rotating cylinder synchronized with a rotating turbine using a timing belt mechanism without needing any external power source. Unlike conventional flow deflectors, the device is not placed in front of the turbine. Instead, it is placed parallel to the turbine position. The optimum device diameter and position are determined using the Taguchi optimization method. The device diameter and its position (Lateral distance, Longitudinal distance, and Location; left and right) are selected as controllable process parameters, and the Cp as the performance output. The Taguchi L16 orthogonal array is selected as the Design of the Experiment (DOE). From the Taguchi analysis, the optimum device parameter improves the Cp by up to 0.3877 at TSR 0.9, a 55.64% improvement relative to the case without the device. The highest Cp achieved is 0.4450 at TSR 1.1, with an 83.73% improvement relative to the case without the device. ANOVA results suggest that the Cp is greatly influenced by both the device diameter and lateral distance. The proposed device improves the overall performance of the Savonius turbine over a wide range of TSR.
This paper presents the study of infrared (IR) reflow oven characteristics for suitable operating conditions of the flexible printed circuit board (FPCB) in the reflow soldering process. A computer-based model that imitates a real-time oven was developed with practical boundary conditions. Since the radiation effect is dominant in the reflow process, a discrete ordinate (DO) model was selected to simulate the effect. The experimental work acts as a benchmark and the reflow profile was set to follow the standards of JSTD-020E. The simulation of the model has a great consensus between the experimental data. It was found that the temperature distribution was inhomogeneous along with the phases. The FPCB surface also has a higher surface temperature than oven air during the operating reflow profile. An in-depth study using the simulation approach reveals that the temperature distribution of the desktop reflow oven is dependent on several factors, namely fan speed, FPCB position, and FPCB thickness. The rotational fan generates an unsteady flow that induces inhomogeneous temperature at different positions in the reflow oven cavity. The results are useful for studying further improvements to achieve temperature uniformity within the oven chamber.
The Savonius wind turbine is a vertical-axis wind turbine invented in 1930s consisting of a cylindrical drum with semi-circular blades attached to the drum. It is popular for its simple design, low costs, and self-starting ability, making it feasible for rural areas. As a rotating device, the blade is considered an important component of the Savonius turbine because it captures energy from omni-directional wind flow and converts it into mechanical/electrical energy. Blade corrosion can cause a surface degradation which affects blade's aerodynamic and structural performance. The relation between surface roughness and turbine performance has been addressed in various studies, however, most of these studies focussed on horizontal-axis wind turbine (HAWT). This study analysed the performance of a static Savonius turbine using three-dimensional (3D) computer simulation at different blade angle positions through one-way fluid-structure-interaction (FSI) in terms of static coefficients, von Mises stresses and deformation with different surface roughness at different wind velocity. The simulation reveals that the position with highest static torque coefficient is when the turbine is resting at 15o with respect to the flow direction. The flow velocity increases the performance however, surface roughness deteriorates the flow and decreases the static coefficient. The simulation herein predicts no structural failure and different materials exhibit different maximum stress and deformation showing the importance of material selection in turbine blade development. The findings from this study helps finding a suitable material for the development of Savonius turbine from a material point of view to minimize turbine downtime and potentially save cost
Vertical axis wind turbines are wind turbines with the rotor axis perpendicular to the ground, designed to harness wind energy for electricity generation. The primary cause of low-efficiency Savonius turbines is the negative torque contribution from the returning blade. A Savonius turbine is a type of turbine characterized by its rotational direction orthogonal to the passing fluid flow and the flow interaction with advancing and returning blades, generating torque primarily through drag forces. Thus, the study proposes a novel design of a cylindrical deflector with splitters and a barrier to offset the flow field to the returning blades. This study aims to maximize the efficiency of conventional Savonius turbines using the cylindrical deflector with splitters and a barrier via a combination of computational fluid dynamics simulations and the Taguchi optimization method. The Taguchi method is used to determine the best combination of specified characteristics such as the length of the barrier (Ls/D), the barrier attachment angle (α), and the geometric shape of the cylinder deflector with a splitter and a barrier. The tip speed ratio (λ) for this study is fixed at λ = 1. The simulations and additive model revealed that the optimal combination in this study is a cylinder deflector with double wake splitters positioned at the top and middle of the deflector. The deflector is oriented parallel to the flow, and a barrier placed at the bottom of the deflector is oriented orthogonal to the flow. The optimal configuration has Ls/D ratio of 0.9 and a barrier attachment angle (α) of 10°. Therefore, the ideal combination was found to produce a power coefficient equivalent to 0.459, indicating that the performance of Savonius turbines increases by around 61% compared to previous studies.