Michal Venglár

Dr. Michal Venglár

Slovak University of Technology, Faculty of Civil Engineering, Department of Structural Mechanics
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 August 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Milan SokolMilan Sokol
Milan Sokol
Michal VenglárMichal Venglár
Michal Venglár
KLKatarína Lamperová
Katarína Lamperová
MMMonika Márföldi
Monika Márföldi
The article presents the development of a SHM (Structural Health Monitoring) strategy intended to confirm the improvement of the load-bearing capacity of a bridge over the Ružín Dam using static and dynamic load tests, as well as numerical simulations. The paper comprises measurements of the global response of the bridge to prepare a verified and validated FEM (Finite Element Method) model. A complex measuring system used for the tests consisted of two main parts: an interferometric IBIS-S (Image by Interferometric Survey-Structures) radar and a multichannel vibration and strain data logger. Next, structure–vehicle interactions were modelled, and non-linear numerical dynamic analyses were performed. As a result, the time histories of displacements of the structure from traffic effects were obtained. Their comparison with IBIS-S radar records proves that this method can be effectively used for assessing bridges subjected to common traffic loads. The results (measured accelerations) obtained by local tests in external pre-stressed cables are presented and a convenient method for acquiring the axial force in the cables is proposed.

31 October 2022 in Acta Polytechnica
Verified
Journal Article
Open access
PDF file
Michal VenglárMichal Venglár
Michal Venglár
KLKatarína Lamperová
Katarína Lamperová
MSMilan Sokol
Milan Sokol
Non-destructive Structural Health Monitoring techniques can be incorporated into bridge integrity management by assessing structural conditions. This paper describes a performance assessment of a steel truss railway bridge in Bratislava using vibration-based techniques as a further part of maintenance in addition to standard visual inspections. To obtain the necessary data, a multipurpose measuring system was used. Various types of data were measured, e.g. accelerations, strains, and displacements. The advantage of the multipurpose measuring system was that the traffic over the bridge was not restricted, even though the bridge carries only a single curved track. Two test campaigns were conducted to assess the performance of the bridge. One campaign was devoted to measuring ambient vibrations in order to perform the operational modal analysis, and the second was carried out to measure strains and displacements during a train passage. The results show a successful system identification of the structure using ambient vibrations; and a finite element model was verified and validated by a comparison of strains and displacements, as well as by modal parameters. According to the results obtained, the structural health of the investigated bridge was satisfactory.

13 October 2020 in Structural Concrete
Verified
Journal Article
Closed access
PDF file
Michal VenglárMichal Venglár
Michal Venglár
MSMilan Sokol
Milan Sokol

1 December 2017 in Pollack Periodica
Verified
Journal Article
Closed access
Milan SokolMilan Sokol
Milan Sokol
Michal VenglárMichal Venglár
Michal Venglár
The primary aim of the paper is to present a simple method for determining the changes in stiffness of a composite beam. The experimental model was made from wood and plaster boards. It was simply supported beam with a length of 4 m. Accelerations were measured at 24 points along the beam. In either case data for intact and damaged models were acquired. The identification of the damage was done using a code developed by the authors. The vertical mode-shapes were analyzed, so changes in the stiffness could be detected.

29 August 2023
Verified
Book Chapter
Closed access
PDF file
Michal VenglárMichal Venglár
Michal Venglár
DBDaniel Beutelhauser
Daniel Beutelhauser
NJNorbert Jendželovský
Norbert Jendželovský
MSMarian Sykora
Marian Sykora

1 January 2016 in Procedia Engineering
Verified
Journal Article
Open access
Milan SokolMilan Sokol
Milan Sokol
Michal VenglárMichal Venglár
Michal Venglár
The article deals with a part of structural health monitoring (SHM) of in scale model. Investigated experimental model is similar to the bridge situated in the western part of Slovakia. After laboratory tests, the work continued with in-situ monitoring of original bridge. During the first stage of testing only the basic dynamic characteristics - mass and stiffness have been verified. Therefore, the different boundary conditions were assumed and namely boundary conditions for cantilever beam instead of those for simply supported beam. This set up allowed for easier construction of boundary conditions. Many difficulties have occurred during the preparation and validation, e.g. different thickness of individual cross-sections, modelling of hinge joints according to the experimental model, modelling of real supports, appropriate parameters of bolts, etc. It was necessary to measure every single cross-section because of the big variation between them. The emphasis was done to modelling of the selected joints especially of the set of 6 bolts on two diagonals of the bridge. The changes in dynamic characteristics according to the different numbers of bolts in a joint have been measured. At the beginning, the natural frequencies were calculated and compared with the test for both cases of model boundary conditions. Modal analysis of the structure was performed in FEM software ANSYS. After a few steps of tuning, the result was sufficiently precise and the difference between measured and analyzed results was small. Finally, the test set up and numerical model similarity was quite acceptable. The next step which is currently being started is the investigation of the damage in joints of two diagonals. The methodology of dynamic testing appropriate for the identification is now being verified