Wood polymer composites (WPC) are sensitive to moisture because of the hydrophilic nature of the wood fibers. The main objective of this study was to improve the dimensional stability of WPCs by coating. Polypropylene and polylactic acid were reinforced by three pulp fibers (kraft, thermomechanical (TMP), and chemothermomechanical (CTMP)) at three fiber contents (50, 60, and 70% w/w). The resulting WPCs were coated using two commercial coatings, epoxy and acrylic. Kraft fiber WPCs were less sensitive to moisture than TMP and CTMP WPCs. These differences were explained by the crystallinity of the kraft fibers and their better interfacial adhesion to the polymers. The epoxy coating proved to be more effective than the acrylic coating and significantly reduced the water absorption and the thickness swell for all formulations. Negative relationships between the contact angle and water absorption were obtained. These relationships depend on the fiber content and type, the matrix nature, and the coating.
Nowadays, 3D PLA-printed parts are widely used in many applications, essentially using the fused filament fabrication technique. While the influence of printing parameters on quasi-static mechanical characterization has been extensively considered within the literature, there are limited accounts of this effect on fatigue performance. The two main aims of this research are first to investigate the effects of the infill density percentage on the fatigue life of dog-bone samples under rotating bending cycling loads, and second to model the fatigue life using Wöhler and Basquin models. The experiments exhibit a high variability of results, especially for low cyclic loads. The S–N curves show that the number of cycles at failure increases with the increase in the infill density percentage and decreases with the increase in loads. Investigations allow the formulation of each constant model as a function of the infill density percentage. The new fatigue model formulations exhibit good agreement with the experimental data. As an outcome of this study, the fatigue model for 3D-printed parts may be expressed as a function of the infill density percentage using fewer tests in the future and for other polymers used in fused filament fabrication.
7 August 2023 in Mathematics and Computers in Simulation
The moisture sensitivity of wood–polymer composites (WPCs) is mainly related to their hydrophilic wood components. Coatings are among the alternatives that improve the dimensional stability of these composites. However, the adhesion of most coatings to the WPC surface is generally poor. Thus, chemical and/or mechanical treatments should be applied to the WPC surface to improve the coating adhesion. Therefore, the main objective of this study was to improve the adhesion coating of polypropylene (PP) WPCs through a chromic treatment. PP was reinforced by three different pulp fibers (kraft, thermomechanical (TMP), and chemothermomechanical (CTMP)) at three fiber contents (50, 60, and 70% w/w). A chromic treatment was applied to the PP-based WPCs to activate the surface of the composites and alter their roughness parameters, creating a higher interfacial zone that improved the bonding of the epoxy coating to the surface of the PP composites. The chromic treatment increased the roughness of the surface. An increase in profile and surface parameters was observed after treatment. This treatment modified the chemical composition of the surface by creating polar carbon–oxygen groups and increasing the carbonyl and hydroxyl indexes.
Real-time control and monitoring are some of the main goals of Industry 4.0. To meet these requirements, sensors are needed at every step of the production process. Wireless sensors (WS) are better suited due to their flexibility but are limited in energy. In this work, kinetic energy harvesting using piezoelectric technologies are considered to ensure the energy autonomy of a Wireless Sensor Network (WSN). First, unlike most existing works, this paper focuses on WSN rather than a single WS since the control of the entirety of most industrial processes requires several WSs. The solution proposed here is based on deep learning of the harvestable power signals at each sensor deployed on the monitoring system. Specifically, vibration measurements were performed at 12 locations on an ore crushing mill in a mine. From there, a mechanical–electrical conversion model considering the system’s dynamics was set up to evaluate the power profile each of the WSs can harvest. Considering that the harvestable power has many peaks due to the different operating states of the engine, we first proposed a Predictor of the Harvestable Power from Vibrations (PHPV). Using a large database, compared to a state-of-the-art predictor, the Predictor of the Harvestable Energy from vibrations (PHEV) allows for significantly reducing the Root Mean Square Error (RMSE). More specifically, the lowest reduction achieved for RSME ranged from 9.4 μW (with PHEV) to 5.9 μW (with PHPV). A decrease in RMSE ranging from 18.45 to 4 μW was obtained for another measurement point. Since harvest rates differ from one location to another, a Hierarchical Energy-Balancing Protocol (HEBP) is proposed to maximize the number of WS capable of transmitting information about the system’s state, thus avoiding an interruption of the network coverage. In the HEBP, it is envisaged that some WSs, besides transmitting data, will supply other nodes with an energy deficit to allow them to communicate information about their location. For a minimum packet size of up to 1100 bits, the energy autonomy of all the WSs is ensured, unlike only 66% of the nodes with the previous protocols.
1 December 2015 in The International Journal of Multiphysics
The use of several developmental approaches is the researchers’ major preoccupation with the DARRIEUS wind turbine. This paper presents the first approach and results of a wide computational investigation on the aerodynamics of a vertical axis DARRIEUS wind turbine based on the MAGNUS effect. Consequently, wind tunnel tests were carried out to ascertain overall performance of the turbine and two-dimensional unsteady computational fluid dynamics (CFD) models were generated to help understand the aerodynamics of this new performance. Accordingly, a moving mesh technique was used where the geometry of the turbine blade was cylinders. The turbine model was created in Gambit modeling software and then read into fluent software for fluid flow analysis. Flow field characteristics are investigated for several values of tip speed ratio (TSR), in this case we generated a new rotational speed ratio between the turbine and cylinder (δ = ωC/ωT). This new concept based on the MAGNUS approach provides the best configura...