This paper presents the design, fabrication, and experimental validation of a metal 3D-printed mechanically tunable cavity resonator operating in the hybrid TM–coaxial resonant mode for the broadband characterization of liquid permittivity. The proposed structure was developed based on a cylindrical cavity by incorporating a disc-terminated metallic tuning stub, which enables continuous frequency adjustment from 0.5 GHz to 3.0 GHz while maintaining a maximum unloaded Q-factor of 284 at 1 GHz under air-filled conditions. The tuning mechanism allows for precise frequency selection for characterizing materials exhibiting frequency-dependent permittivity. To demonstrate its sensing capability, the resonator was applied to characterize ethanol–water mixtures, where resonant frequency shifts were correlated with ethanol concentration at representative baseline frequencies of 1.00 GHz, 2.00 GHz, and 2.94 GHz. The sensor achieved frequency/dielectric constant resolutions of 0.39, 1.34, and 4.20 MHz and average concentration errors of 1.25%, 3.73%, and 2.49%, respectively. Moreover, polynomial fitting models enabled the accurate extraction of dielectric constants with an average deviation below 0.5% compared with a commercial dielectric probe system. The combination of frequency tunability, compact geometry, and compatibility with additive manufacturing establishes the proposed cavity resonator as a versatile platform for broadband dielectric spectroscopy, chemical sensing, and liquid characterization.
5 March 2024 in IEEE Open Journal of Antennas and Propagation
In this study, a low-cost dual-chip RFID tag antenna is proposed for indoor localization. The antenna integrates two RFID chips, each generating opposing radiation patterns. Angle-of-arrival based localization is performed with a single reader by analyzing the Received Signal Strength Indicator (RSSI) and the RSSI ratio of both chips. The antenna incorporates a mechanically adjustable reflector at the back that allows simple beam elevation control to tune the antenna for different indoor environments. The proposed dual-chip tag was measured in an indoor environment with different beam configurations. The localization is performed using a simple sinusoidal regression model with three model parameters and a linear regression model with two model parameters to fit the RSSI ratio of both chips and the RSSI of each individual chip, respectively. The proposed technique yields an average angle-of-arrival error better than 6.6∘ within the tag’s horizontal detection range of 4.2 meters.
In this work, an on-glass antenna is proposed for IoT and smart building applications. The dielectric properties of five common glass types used in architecture were investigated. Clear glass, 3 mm thick, was selected as the substrate. The antenna is a rectangular monopole with a coplanar waveguide feed and an asymmetric ground. It was designed and simulated using Ansys HFSS, then fabricated using clear glass and copper tape. Measurements of the reflection coefficient and radiation pattern showed good agreement with simulations. The antenna exhibits a bidirectional radiation pattern, with 2.8 dBi gain and 94.82% radiation efficiency at 2.1 GHz and 3.9 dBi gain and 95.72% radiation efficiency at 2.4 GHz, respectively. A −10 dB bandwidth of 650 MHz (29.3%) centered at 2.215 GHz was achieved. The proposed antenna shows promise for integration with architectural glass elements in smart building applications, such as smart glass doors and windows.
This work presents microwave sensing of ethanol concentration in ethanol–water mixtures using a low-cost 3D-printed cavity resonator. The objective is to realize a customizable liquid sensor that combines high measurement accuracy with inexpensive, in-house fabrication. The cylindrical cavity is fabricated from polylactic acid using fused deposition modeling and metallized on its inner surface with copper tape. The resonator operates in the TM010 mode with a resonant frequency of 3 GHz. A standard 1.5 mL centrifuge tube is used as a modular sample holder and inserted through a circular opening in the top endcap of the cavity. The quality factor of the air-filled cavity is 200, which decreases to 37.3 when the cavity is loaded with deionized water. As an application example, ethanol concentrations in ethanol–water mixtures are determined using both the resonant frequency and the peak magnitude of the transmission coefficient (|S21|). For ethanol concentrations between 20% and 100%, the concentration can be accurately extracted from the resonant frequency alone: a quartic calibration curve yields a coefficient of determination , an average sensitivity of approximately 8.4 MHz/% ethanol, and a mean absolute error of about 0.58% on the calibration set. In addition, a cubic calibration based on the peak over the 0–90% concentration range achieves a mean absolute error of approximately 0.52% on the calibration set and about 0.55% on an independent validation set covering 5–85% ethanol. Comparison with conventionally machined metal cavities shows that the proposed 3D-printed cavity achieves a high Q-factor at significantly lower cost and can be fabricated in-house using a standard 3D printer. These results demonstrate metrologically relevant performance in terms of low error and high sensitivity using a low-cost and easily replicable platform for microwave liquid sensing in biomedical and chemical engineering applications.
In this paper, a transparent UHF-RFID tag antenna is proposed for seamless integration into smart city IoT applications. The antenna features a transparent radiator made from an Indium Tin Oxide (ITO) conductive film on a glass substrate. The antenna design incorporates a loop structure with a meander line and a T-matching network to match the input impedance of the RFID chip. CST Microwave Studio was used to simulate the antenna performance. A parametric study was conducted to optimize the design and analyze the antenna performance based on different properties of the glass substrate and the ITO film. The proposed RFID tag antenna is designed on a 3mm thick Corning 0080 glass substrate and exhibits a radiation efficiency of 37% with a gain of -2.10dBi. The relatively low radiation efficiency is caused by the high dielectric loss of the glass substrate and the high conductive loss of the ITO film. The proposed design aims for the best possible efficiency of a transparent RFID tag antenna despite the high loss of the materials. Compared to a conventional RFID tag, the proposed transparent tag offers seamless integration with architectural glass structures in smart buildings at the cost of a lower read range. With the length of 0.20 λ $o$ ,the proposed tag antenna is considered electrically small.