Naz MARDANİ

Dr. Naz MARDANİ

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 July 2024 in Buildings
Verified
Journal Article
Open access
PDF file
YKYahya Kaya
Yahya Kaya
VKVeysel Kobya
Veysel Kobya
AMAli Mardani
Ali Mardani
NMNaz MARDANİ
Naz MARDANİ
HBHatice Elif Beytekin
Hatice Elif Beytekin
The production of cement, an essential material in civil engineering, requires a substantial energy input, with a significant portion of this energy consumed during the grinding stage. This study addresses the gap in the literature concerning the collective impact of key parameters, including ball size, feed rate, and mill speed, on grinding efficiency. Nine spherical balls, ranging from 15–65 mm, were utilized in six distinct distributions, alongside varying feed rates and mill speeds. ANOVA, Taguchi, and regression analyses were employed to explore their influence on grinding efficiency and cement properties. The findings revealed that ball size variation significantly affects grinding performance, with smaller diameter balls yielding higher efficiency due to increased abrasion and fine formation. Conversely, elevating mill speed generally diminishes grinding efficiency, particularly at speeds approaching 90% of the critical speed, impacting ball shoulder and foot angles. Moreover, increasing the feed rate affects the grinding performance differently based on ball distribution, with finer distributions experiencing adverse effects. Signal-to-noise ratios facilitated determining the optimal control factor levels to minimize energy consumption. Quadratic regression models exhibited strong predictive capabilities for energy consumption in grinding. Ultimately, the optimal grinding performance was achieved with Bond-type ball distribution No. 6, considering ball size, mill speed, and feed-rate interactions, albeit with considerations regarding grinding time and energy efficiency.

21 February 2025 in Materials
Verified
Journal Article
Open access
PDF file
TKTuğçe İsafça Kaya
Tuğçe İsafça Kaya
YKYahya Kaya
Yahya Kaya
NMNaz MARDANİ
Naz MARDANİ
AMAli Mardani
Ali Mardani
ADAdem Doğangün
Adem Doğangün
Lime-based mortars, frequently used in historic structures, are classified as hydraulic and non-hydraulic according to how they gain strength. In the past, various methods were used to improve the strength and durability properties of lime-based hydraulic mortars such as Khorasan mortar. Today, in studies carried out to increase the strength of lime-based mortars, the effects of binders, aggregates, and additives, which are the basic components of the mortar, are examined. In this study, the mechanical properties of Khorasan mortar mixtures, which are frequently used in the restoration of historical structures, were examined under the influence of different parameters. In particular, the effects of variables such as aggregate type and ratio (river sand and crushed brick), binder type and ratio (natural hydraulic lime, metakaolin, and blast furnace slag), and water/total dry material ratio on the strength of mortars were investigated experimentally. In the experimental study, two different aggregate types (river sand and crushed brick) were used in 1/3 and 1/2 ratios, and three different binders (natural hydraulic lime, metakaolin, and blast furnace slag) were used in different ratios. The water-to-total-dry-material ratios were set at 0.2 and 0.25. Standard test samples were then created from the prepared mortar mixtures, and their flexural and compressive strengths were assessed at 28 and 56 days. A statistical analysis of the experimental data was conducted using the Taguchi method, allowing for a detailed examination of how the different parameters influenced the strength of the mortars. Through this analysis, the optimal mixture ratios that maximized mortar strength were successfully identified.

22 May 2025 in Materials
Verified
Journal Article
Open access
PDF file
Murteda ÜNVERDİMurteda ÜNVERDİ
Murteda ÜNVERDİ
YKYahya Kaya
Yahya Kaya
NMNaz MARDANİ
Naz MARDANİ
AMAli Mardani
Ali Mardani
In this study, the effects of different fiber types on improving the high-temperature performance of roller-compacted concrete (RCC) were comprehensively investigated. For this purpose, 60 mm long steel (S), polypropylene (PP), and environmentally sustainable waste steel (WS) fibers were incorporated into RCC at volumetric ratios of 0%, 0.25%, 0.50%, 0.75%, 1.00%, and 1.25%. The prepared specimens were exposed to controlled conditions at 25 °C (room temperature), 300 °C, 600 °C, and 900 °C, and the influence of thermal exposure on compressive strength and permeability characteristics was thoroughly evaluated. The findings revealed that high temperatures led to significant changes in the physical and mechanical properties of the concrete. Notably, at elevated temperatures such as 600 °C and 900 °C, S and WS fibers were found to reduce strength loss by limiting the propagation of microcracks within the concrete matrix. However, PP fibers were observed to lose their effectiveness at high temperatures due to melting in the range of approximately 160–170 °C, which negatively affected mechanical performance. One of this study’s key findings is that waste steel fibers offer a sustainable alternative while exhibiting comparable performance to conventional steel fibers. These results highlight the potential of recycling industrial waste to reduce environmental impact and lower overall costs.

6 July 2024 in Buildings
Verified
Journal Article
Open access
PDF file
HŞHatice Gizem Şahin
Hatice Gizem Şahin
AMAli Mardani
Ali Mardani
NMNaz MARDANİ
Naz MARDANİ
In this study, a procedure for mixture design was proposed with the aim of meeting the requirements of extrudability, buildability, and shape stability in 3D printable concrete. Optimum water/binder ratio, sand/binder ratio, binder type, utilization ratio, aggregate particle distribution and quantity, and type and utilization ratio of chemical admixtures were determined for 3D printable concrete in terms of print quality and shape stability criteria. A total of 32 different mixtures were produced. It was determined that mixtures produced using a binder content with approximately 40% fly ash, a w/b ratio of 0.35, and aggregates with Dmax of 1 mm exhibit acceptable characteristics. Investigations were also conducted into the thixotropic behavior, rheological characteristics, and mechanical properties of the mixes that were deemed acceptable. As a result, it was determined that the increase in the amount of fly ash usage positively affected the buildability of the printed layers. Additionally, the dynamic yield stress ranging from 114 to 204 Pa, viscosity ranging from 22 to 43 Pa.s, and structural build-up value ranges suitable for the production of 3D printable concrete mixtures were determined.

5 June 2025 in Polymers
Verified
Journal Article
Open access
PDF file
YKYahya Kaya
Yahya Kaya
HÖHasan Tahsin Öztürk
Hasan Tahsin Öztürk
VKVeysel Veysel Kobya
Veysel Veysel Kobya
NMNaz MARDANİ
Naz MARDANİ
AMAli Mardani
Ali Mardani
In this study, the compatibility of polycarboxylate ether-based water-reducing admixtures (PCE) with cements produced with different types and dosages of grinding aids (GA) was experimentally and statistically investigated. A total of 203 paste mixtures were prepared using seven different types of GA and one type of PCE at different dosages. The Marsh funnel flow time and mini-slump values of the mixtures were compared. A modeling study was performed using the experimental data. In this direction, Classical Regression Analysis (CRA), Multivariate Adaptive Regression Splines (MARS), and Artificial Neural Networks (AOMA-ANN) were applied. Innovative approaches, AOMA-ANN (AIP) and AOMA-ANN (ONIP), were introduced. The results showed adverse effects on flow performance with increased GA utilization, except for TEA-based GA. TEA-type GA had the lowest flow performance. AOMA-ANN (ONIP) exhibited the best performance in modeling. Marsh funnel flow-time modeling with AOMA-ANN (ONIP) considered parameters such as sieve residue at 60 microns, the number of molecules per fineness, the density of GA, the pH value of GA, and the PCE dosage. Mini-slump modeling with AOMA-ANN (ONIP) considered parameters such as sieve residue at 60 microns, the density of GA, the pH value of GA, and the PCE dosage.

9 June 2025 in Materials
Verified
Journal Article
Open access
PDF file
YKYahya Kaya
Yahya Kaya
VKVeysel Veysel Kobya
Veysel Veysel Kobya
MEMURAT ESER
MURAT ESER
NMNaz MARDANİ
Naz MARDANİ
MBMetin Bilgin
Metin Bilgin
AMAli Mardani
Ali Mardani
To develop more environmentally friendly and sustainable cementitious systems, the use of grinding aids (GAs) during the clinker grinding process has increasingly gained attention. Although the mechanisms of the action of grinding aids (GAs) are known, the selection of an effective grinding aid (GA) can be difficult due to the complexity of appropriate selection criteria. For this reason, it is important to model the effect of GA properties on grinding performance. In this study, seven different types of GAs were used in four different dosages, and time-dependent grinding was performed. The Blaine fineness values of cements were compared after each grinding process. In addition, the modeling of these parameters using machine learning and ensemble learning methods was discussed. The Synthetic Minority Over-sampling Technique (Smote) was used to generate artificial data and increase the number of data for the grinding efficiency experiment. The data were modeled using methods such as Artificial Neural Networks (ANNs), Attentive Interpretable Tabular Learning (TabNet), Random Forests (RFs), and the XGBoost Regressor (XGBoost), and the ranking of the parameters affecting the Blaine properties was determined using the XGBoost method. The XGBoost method achieved the best results in the MAE, RMSE, and LogCosh metrics with values of 21.0384, 33.7379, and 15.4846, respectively, in the experimental modeling studies with augmented data. This study contributes to a better understanding of the relationship between GA selection and milling process performance.