Noor Azwan Shairi

Dr. Noor Azwan Shairi

Universiti Teknikal Malaysia Melaka, Melaka, Malaysia
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 July 2022 in IEEE Sensors Journal
Verified
Journal Article
Closed access
Syah AlamSyah Alam
Syah Alam
ZAHRILADHA ZAKARIAZAHRILADHA ZAKARIA
ZAHRILADHA ZAKARIA
ISIndra Surjati
Indra Surjati
Noor Azwan ShairiNoor Azwan Shairi
Noor Azwan Shairi
MAMudrik Alaydrus
Mudrik Alaydrus
TFTeguh Firmansyah
Teguh Firmansyah
This study proposes a single-port dual-band independent microwave sensor for detecting solid materials. The sensor structure consists of a pair U-shaped resonators connected by a power divider and a microstrip feed line with an impedance of 50 Ohms with two different sensing hotspots. The $1^{\text {st}}$ and $2^{\text {nd}}$ resonators operate at a frequency of 1.200 GHz and 2.100 GHz, respectively. The type of material under test (MUT) is a standard material with a size of 10 mm $\times10$ mm (RO5880, RO4003C, and FR4). The proposed sensor had a very high accuracy compared with both of using permitivitty from datasheet and calibrated frequency from simulation for the $1^{\text {st}}$ and $2^{\text {nd}}$ resonator, respectively. Moreover, the pair of the U-shaped resonators had independent performances and they did not affect each other when the MUT was loaded. Furthermore, it can also operate with single-port measurement, which is a more efficient resource. Finally, the proposed microwave sensor can be a promising solution for detecting different permittivity of solid materials independently with high accuracy for applications such as the food industry, material quality control, and biomedical.

1 December 2011
Verified
Conference Paper
Closed access
Noor Azwan ShairiNoor Azwan Shairi
Noor Azwan Shairi
BABadrul Hisham Ahmad
Badrul Hisham Ahmad
AKA. C. Z. Khang
A. C. Z. Khang
A design and analysis of broadband high isolation of discrete packaged PIN diode Single-Pole Double-Throw (SPDT) switch is presented. Many applications of wireless data communication are implementing Time Division Duplex (TDD) switching such as UMTS-TDD (in 3G technologies), LTE (in 4G technologies), HiperLAN, HiperMAN, WiFi, WiMAX and WiBRO. A broadband high isolation of SPDT switch is needed to provide these multimarket applications at different frequency bands. In this paper, three different circuit topologies (Type A, Type B and Type C) targeted for broadband high isolation are designed and analyzed. The SPDT switches are based on the discrete packaged PIN diode that available in the market for switching control. Analysis of the various configurations is done in order to select the most suitable topology for broadband high isolation SPDT switch. As results, Type C has been chosen for prototyping and measurement. In simulation and measurement, the isolation is higher than 25 dB from 0.5 to 3 GHz compared with Type A and Type B.

10 May 2023 in IEEE Sensors Journal
Verified
Journal Article
Closed access
Syah AlamSyah Alam
Syah Alam
ZAHRILADHA ZAKARIAZAHRILADHA ZAKARIA
ZAHRILADHA ZAKARIA
ISIndra Surjati
Indra Surjati
Noor Azwan ShairiNoor Azwan Shairi
Noor Azwan Shairi
MAMudrik Alaydrus
Mudrik Alaydrus
TFTeguh Firmansyah
Teguh Firmansyah
This paper proposes the integration of microwave sensors (MS) and antenna sensors (AS) for contact and non-contact characterization of solid materials. Integration between MS and AS were determined based on the reflection coefficient (S11) where S11 of ≥ -10 dB was proposed as MS and S 11 of ≤ -10 dB was proposed as AS. The proposed sensor consists of a dual T-Shaped resonator with single port operating at a resonant frequency of f r1 = 1.81 GHz for MS and f r2 = 2.34 GHz for AS using FR-4 substrate with ε r of 4.3, tan δ of 0.0265 and thickness of 1.6 mm. Furthermore, the two resonant frequencies had independent characteristics with different sensing hotspots. MS are proposed for permittivity detection of the Material Under Test (MUT) for contact detection while non-contact detection is proposed by utilizing AS. The procedure for contact detection was carried out by placing the material under test on the surface of the sensor while non-contact detection was carried out by placing the MUT with an air gap between the MUT (d) and the AS was 0.5 - 1.5 mm. The measurement results showed that the average accuracy was 99.30% and 99.31% for the MS and AS for the permittivity range of 1 - 6.15 while the normalized sensitivities of the proposed sensors were 1.15 % and 0.16%, respectively. The results of this research are novel and can be recommended for several purposes related to biomedical and pharmaceutical industries requiring contact and non-contact detection of material characterization.

1 January 2017 in Progress in Electromagnetics Research C
Verified
Journal Article
Open access
PDF file
AAAmmar Alhegazi
Ammar Alhegazi
ZAHRILADHA ZAKARIAZAHRILADHA ZAKARIA
ZAHRILADHA ZAKARIA
Noor Azwan ShairiNoor Azwan Shairi
Noor Azwan Shairi
IMRAN MOHD IBRAHIMIMRAN MOHD IBRAHIM
IMRAN MOHD IBRAHIM
Sharif AhmedSharif Ahmed
Sharif Ahmed
This study presents a novel technique for designing an ultra-wideband (UWB) filteringantenna with dual sharp band notches. This design is composed of a modified monopole antenna integrated with resonant structures. The monopole antenna is modified using microstrip transition between the feedline and the patch. In addition, block with a triangle-shaped slot is loaded on each side of the ordinary circular patch to produce wide bandwidth with better return loss and higher frequency skirt selectivity. The resonant structures are constructed using two double split ring resonators (DSRR) loaded above the ground plane of the antenna to produce dual band notches and filter out WiMAX (3.3-3.7 GHz) and HiperLAN2 (5.4-5.7 GHz) frequencies. The band notch position is controlled by varying the length of the DSRR. The reconfigurability feature is achieved by using two PIN diode switches employed in the two DSRR. The measured results show that the proposed filtering-antenna provides wide impedance bandwidth from 2.58 to 15.5 GHz with controllable dual sharp band notches for WiMAX and HiperLAN, peak realized gain of 4.96 dB and omnidirectional radiation pattern.

1 December 2012
Verified
Conference Paper
Closed access
ZAHRILADHA ZAKARIAZAHRILADHA ZAKARIA
ZAHRILADHA ZAKARIA
Noor Azwan ShairiNoor Azwan Shairi
Noor Azwan Shairi
RSR. Sulaiman
R. Sulaiman
WSW. Y. Sam
W. Y. Sam
This paper presents the design of reconfigurable defected ground structure (DGS) resonator that can be integrated with ultrawide-band (UWB) microwave filter to produce bandpass and bandstop response simultaneously. The reconfigurable DGS is designed based upon coplanar waveguide (CPW) technology to exhibit bandstop characteristic at 3.5 GHz and 5.5 GHz using FR-4 on a 1.6 mm dielectric substrate thick with dielectric constant ε r = 4.6. The simulation performance shows promising results that could be further validated during the experimental works. This topology of reconfigurable DGS is useful for applications when the undesired signals need to be removed such as in wideband systems.

1 January 2021 in PRZEGLĄD ELEKTROTECHNICZNY
Verified
Journal Article
Closed access
RKRabiatul Adawiyah Azian Kamaruddin
Rabiatul Adawiyah Azian Kamaruddin
IMRAN MOHD IBRAHIMIMRAN MOHD IBRAHIM
IMRAN MOHD IBRAHIM
Ahmed Jamal Abdullah Al-GburiAhmed Jamal Abdullah Al-Gburi
Ahmed Jamal Abdullah Al-Gburi
ZAHRILADHA ZAKARIAZAHRILADHA ZAKARIA
ZAHRILADHA ZAKARIA
Noor Azwan ShairiNoor Azwan Shairi
Noor Azwan Shairi
TPTeddy Purnamirza
Teddy Purnamirza
This paper aims to investigate and design a radial line slot array antenna (RSLA) with closed ring resonator (CRR) for return loss improvement. The CRR printed on a dielectric substrate with a circumference alignment position attached to the RLSA antenna. The CRR structure used the combination of the four rings with a rectangular shape and showed a response in the range of 25.30 GHz up to 31.40 GHz. It is worth mentioning that applying a gap cavity height (h) of the superstrate layer to the CRR structure is needed to improve the return loss significantly. However, as the superstrate layer of the CRR structure is increased the value of the gap cavity height must be adjustable to ensure that the return loss is maintained at the same resonant frequency. The return loss performance showed a significant improvement from -10.30 dB to -12.34 dB for N4 gap between the antenna and the superstrate.