21 July 2022 in IEEE Sensors Journal
This study proposes a single-port dual-band independent microwave sensor for detecting solid materials. The sensor structure consists of a pair U-shaped resonators connected by a power divider and a microstrip feed line with an impedance of 50 Ohms with two different sensing hotspots. The $1^{\text {st}}$ and $2^{\text {nd}}$ resonators operate at a frequency of 1.200 GHz and 2.100 GHz, respectively. The type of material under test (MUT) is a standard material with a size of 10 mm $\times10$ mm (RO5880, RO4003C, and FR4). The proposed sensor had a very high accuracy compared with both of using permitivitty from datasheet and calibrated frequency from simulation for the $1^{\text {st}}$ and $2^{\text {nd}}$ resonator, respectively. Moreover, the pair of the U-shaped resonators had independent performances and they did not affect each other when the MUT was loaded. Furthermore, it can also operate with single-port measurement, which is a more efficient resource. Finally, the proposed microwave sensor can be a promising solution for detecting different permittivity of solid materials independently with high accuracy for applications such as the food industry, material quality control, and biomedical.
10 May 2023 in IEEE Sensors Journal
This paper proposes the integration of microwave sensors (MS) and antenna sensors (AS) for contact and non-contact characterization of solid materials. Integration between MS and AS were determined based on the reflection coefficient (S11) where S11 of ≥ -10 dB was proposed as MS and S 11 of ≤ -10 dB was proposed as AS. The proposed sensor consists of a dual T-Shaped resonator with single port operating at a resonant frequency of f r1 = 1.81 GHz for MS and f r2 = 2.34 GHz for AS using FR-4 substrate with ε r of 4.3, tan δ of 0.0265 and thickness of 1.6 mm. Furthermore, the two resonant frequencies had independent characteristics with different sensing hotspots. MS are proposed for permittivity detection of the Material Under Test (MUT) for contact detection while non-contact detection is proposed by utilizing AS. The procedure for contact detection was carried out by placing the material under test on the surface of the sensor while non-contact detection was carried out by placing the MUT with an air gap between the MUT (d) and the AS was 0.5 - 1.5 mm. The measurement results showed that the average accuracy was 99.30% and 99.31% for the MS and AS for the permittivity range of 1 - 6.15 while the normalized sensitivities of the proposed sensors were 1.15 % and 0.16%, respectively. The results of this research are novel and can be recommended for several purposes related to biomedical and pharmaceutical industries requiring contact and non-contact detection of material characterization.
17 June 2024 in IEEE Sensors Letters
This letter introduces collaboratively far-field and near-field regions for dual modalities permittivity sensor to characterized solid materials. The proposed sensor comprises a T-shaped resonator featuring a single port embedded with Interdigital capacitor (IDC). The 1 st resonator, operating at fr1 = 2.43 GHz as the long-distance detection utilizes the far field region, while the 2 nd resonator, working at fr2 = 1.64 GHz, functions as the contact detection utilizes the near field region. These resonators possess distinct sensing hotspots, enabling independent utilization. Contact detection is achieved by utilized the near-field region by placing the material under test (MUT) directly above the surface of the 2 nd resonator, while the 1 st resonator for long-distance detection utilized the far-field region by using the interrogator antenna at a distance of d = 10 cm. The experimental results demonstrate that the proposed sensors exhibit a maximum sensitivity of 5.13% and 3.40% for near field and far field detection, respectively. Moreover, the average accuracy for both contact and long-distance detection is 95.99% and 95.16%, respectively, when compared to the permittivity values obtained from the datasheet within the range of 1 - 6.15. This research holds significant practical value for the contact and long-distance characterization of solid materials, particularly in applications such as biomedical, quality control, and pharmaceutical industries.
8 July 2024 in IEEE Access
This paper proposes dual functional microwave sensor for displacement and angular detection of liquid material based on electric coupled (ELC) resonator. The liquid was placed in polystyrene-mm pipe channel filled with water content. The proposed resonator uses a two-port band stop filter operating at a resonant frequency of 2.72 GHz. Polystyrene-mm pipe channels are used to accommodate water samples placed in the sensing area of the sensor in the center of the ELC resonator. Displacement and angular detection were observed based on the shift in the resonant frequency of the resonator. Based on the measurement results, the proposed sensor has a sensitivity for displacement detection of 31.5 MHz/cm with a distance range of d = 1 – 4 cm while for angular detection it is 0.33 MHz/° with a rotation angle of 0 – 9° for polystyrene-mm pipe channel filled with water content. This paper makes a significant contribution by proposed a dual functional microwave sensor for displacement and angular detection that can be recommended for the automotive, robotics and aerospace industries.
16 December 2021 in Jurnal Telematika
The Fifth Generation (5G) communication system promises high data transfer rates. It requires an antenna that can operate with gain and bandwidth at 3.4 – 3.6 GHz frequency range which complies with 5G frequency regulation. This study proposes an optimized 2x1 element array microstrip antenna using inset and slit techniques. The antenna is designed to operate at 3.5 GHz for 5G communication systems. The array method is used to increase the gain value, while inset and slit techniques are used to reduce the reflection coefficient (S11). From the design and simulation results, the reflection coefficient value is – 24 dB and the bandwidth is 360 MHz (3.32 GHz -3.68 GHz), or 10.28%, at a frequency of 3.5 GHz. The use of the array method worked in increasing the gain by 66.67% and the bandwidth by 70.43%, compared to single-element antennas. Sistem komunikasi Generasi Kelima (5G) menjanjikan kecepatan transfer data yang sangat tinggi sehingga memerlukan antena yang dapat bekerja dengan penguatan dan bandwidth pada rentang frekuensi 3,4 hingga 3,6 GHz yang sesuai dengan regulasi frekuensi 5G. Penelitian ini mengusulkan desain antena mikrostrip array 2x1 elemen yang dioptimalisasi menggunakan teknik inset dan slit. Antena dirancang untuk bekerja pada frekuensi kerja 3.5 GHz untuk sistem komunikasi 5G. Metode array digunakan untuk meningkatkan nilai gain dari antena, sedangkan teknik inset dan slit digunakan untuk mereduksi nilai koefisien refleksi (S11) dari antena yang diusulkan. Dari hasil perancangan dan simulasi didapatkan nilai koefisien refleksi – 24 dB dan bandwidth 360 MHz (3,32 GHz hingga 3,68 GHz), atau 10,28%, pada frekuensi 3,5 GHz. Penggunaan metode array berhasil meningkatkan gain sebesar 66,67% dan bandwidth sebesar 70,43% dibandingkan dengan antena single element.
4 February 2025 in IEEE Access
This paper proposes a single-port interdigital capacitor (IDC) resonator based on asymmetric branch feed line with high stability performance for permittivity detection of solid materials with a permittivity range of 1 - 6.15. The microwave sensor is designed using a single-port resonator operating at two different resonant frequencies fr1 = 1.61 GHz and fr2 = 2.52 GHz. Dual band frequency was proposed using asymmetric branch feed line. In addition, to confine the electric field concentration of the resonator, an interdigital capacitor (IDC) structure is proposed as a solution. Furthermore, a copper shield was proposed as conducting material to evaluate performance stability of the sensor from disturbance effect with range of d = 1 cm – 2.5 cm. Based on the measurement results, the sensor has high stability both without and with disturbance with an a Frequency Detection Resolution (FDR) of 0.009 - 0.4 GHz/Δεr, a Normalized Sensitivity (NS) of 0.4% - 4.4%, and an average accuracy of 90% - 95% for both resonance frequencies, respectively. Therefore, this sensor can be recommended for several applications such as biomedical industry, pharmaceuticals and material quality control especially for outdoor measurements that are potentially affected by electromagnetic interference and disturbance.