Nur Sharmila Sharip

Dr. Nur Sharmila Sharip

Universiti Putra Malaysia
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Materials Today: Proceedings
Verified
Journal Article
Closed access
NSNur Sharmila Sharip
Nur Sharmila Sharip
HAHidayah Ariffin
Hidayah Ariffin

27 January 2021 in Polymers
Verified
Journal Article
Open access
PDF file
NSNur Sharmila Sharip
Nur Sharmila Sharip
HAHidayah Ariffin
Hidayah Ariffin
TYTengku Arisyah Tengku Yasim-Anuar
Tengku Arisyah Tengku Yasim-Anuar
Yoshito AndoYoshito Ando
Yoshito Ando
YSYuki Shirosaki
Yuki Shirosaki
NINor Azowa Ibrahim
Nor Azowa Ibrahim
The major hurdle in melt-processing of ultra-high molecular weight polyethylene (UHMWPE) nanocomposite lies on the high melt viscosity of the UHMWPE, which may contribute to poor dispersion and distribution of the nanofiller. In this study, UHMWPE/cellulose nanofiber (UHMWPE/CNF) bionanocomposites were prepared by two different blending methods: (i) melt blending at 150 °C in a triple screw kneading extruder, and (ii) non-melt blending by ethanol mixing at room temperature. Results showed that melt-processing of UHMWPE without CNF (MB-UHMWPE/0) exhibited an increment in yield strength and Young’s modulus by 15% and 25%, respectively, compared to the Neat-UHMWPE. Tensile strength was however reduced by almost half. Ethanol mixed sample without CNF (EM-UHMWPE/0) on the other hand showed slight decrement in all mechanical properties tested. At 0.5% CNF inclusion, the mechanical properties of melt-blended bionanocomposites (MB-UHMWPE/0.5) were improved as compared to Neat-UHMWPE. It was also found that the yield strength, elongation at break, Young’s modulus, toughness and crystallinity of MB-UHMWPE/0.5 were higher by 28%, 61%, 47%, 45% and 11%, respectively, as compared to the ethanol mixing sample (EM-UHMWPE/0.5). Despite the reduction in tensile strength of MB-UHMWPE/0.5, the value i.e., 28.4 ± 1.0 MPa surpassed the minimum requirement of standard specification for fabricated UHMWPE in surgical implant application. Overall, melt-blending processing is more suitable for the preparation of UHMWPE/CNF bionanocomposites as exhibited by their characteristics presented herein. A better mechanical interlocking between UHMWPE and CNF at high temperature mixing with kneading was evident through FE-SEM observation, explains the higher mechanical properties of MB-UHMWPE/0.5 as compared to EM-UHMWPE/0.5.

29 August 2016 in RSC Advances
Verified
Journal Article
Closed access
PDF file
NSNur Sharmila Sharip
Nur Sharmila Sharip
HAHidayah Ariffin
Hidayah Ariffin
MHMohd Ali Hassan
Mohd Ali Hassan
HNHaruo Nishida
Haruo Nishida
YSYoshihito Shirai
Yoshihito Shirai
Lignocellulosic degradation products from superheated steam (SHS) pretreatment of oil palm mesocarp fiber (OPMF) at 190 °C to 240 °C for 1 hour were recovered as a condensate. Compositional analysis of the condensate was carried out and subsequently its potential application as an antifungal agent was investigated. GCMS analysis revealed a total of 62 compounds in the condensate sample from SHS pretreatment at 240 °C, which were identified and classified into ten different groups of aromatic phenolics, furans, pyrans, dioxoles; and open chains ketones, esters, alcohols, aldehydes, alkenes and alkanes. The presence of carboxylic acids was identified by HPLC and the condensate contained acetic, formic, levulinic and succinic acids at concentrations of 1671 mg L−1, 12 320 mg L−1, 831 mg L−1 and 435 mg L−1, respectively. Complete suppression of Ganoderma boninense UPM13 mycelial growth was observed in the agar dilution test, while spore germination of Aspergillus fumigatus UPM2 and Trichoderma asperellum UPM1 was completely inhibited in the spore germination test. The growth suppression of G. boninense, a fungal causing basal stem rot (BSR) disease in oil palm plantation shows the condensate potential benefit to combat the disease.

30 December 2020 in Pertanika Journal of Science and Technology
Verified
Journal Article
Closed access
TYTengku Arisyah Tengku Yasim-Anuar
Tengku Arisyah Tengku Yasim-Anuar
NSNur Sharmila Sharip
Nur Sharmila Sharip
LMLiana Noor Megashah
Liana Noor Megashah
HAHidayah Ariffin
Hidayah Ariffin
NNNor Azlin Muhamad Nor
Nor Azlin Muhamad Nor
Waste paper is the second-highest municipal solid waste collected in Malaysia and as current practice, it is recycled for further use in the manufacturing of low-grade products. Instead of continuously utilizing waste paper for low-grade products manufacturing, it can be used as a feedstock to produce high bioproducts such as cellulose nanofiber (CNF). Hence, this study explored the potential of waste paper as a feedstock for CNF production. The waste paper was subjected to a different number of cycles of wet disk milling (WDM): 0, 5, 10, 15 and 20 cycles. The presence of nano-sized cellulose was confirmed by FE-SEM micrographs, where CNF with diameter size 20 – 40 nm was formed after 10 cycles of milling. It was also revealed that the obtained CNF possessed appropriate properties as a reinforcement material. The tensile strength and Young’s modulus of poly((R)-3-hydroxybutyrate-co- (R)-3-hydroxyhexanoate (PHBHHx) increased by 19 and 12%, respectively after the reinforcement of 1% CNF. Overall, this study portrays that waste paper could be utilized as a raw material for CNF production, without the need for chemical pretreatment.

30 September 2020 in Molecules
Verified
Journal Article
Open access
PDF file
NSNur Sharmila Sharip
Nur Sharmila Sharip
HAHidayah Ariffin
Hidayah Ariffin
EBEzyana Kamal Bahrin
Ezyana Kamal Bahrin
YSYuki Shirosaki
Yuki Shirosaki
YSYuki Shirosaki
Yuki Shirosaki
NINor Azowa Ibrahim
Nor Azowa Ibrahim
Incorporation of nanocellulose could improve wear resistance of ultra-high molecular weight polyethylene (UHMWPE) for an artificial joint application. Yet, the extremely high melt viscosity of the polymer may constrict the mixing, leading to fillers agglomeration and poor mechanical properties. This study optimized the processing condition of UHMWPE/cellulose nanofiber (CNF) bionanocomposite fabrication in triple screw kneading extruder by using response surface methodology (RSM). The effect of the process parameters—temperature (150–190 °C), rotational speed (30–60 rpm), and mixing time (30–45 min)—on mechanical properties of the bionanocomposites was investigated. Homogenous filler distribution, as confirmed by scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) analysis, was obtained through the optimal processing condition of 150 °C, 60 rpm, and 45 min. The UHMWPE/CNF bionanocomposites exhibited improved mechanical properties in terms of Young’s and flexural modulus by 11% and 19%, respectively, as compared to neat UHMWPE. An insignificant effect was observed when maleic anhydride-grafted-polyethylene (MAPE) was added as compatibilizer. The obtained results proved that homogenous compounding of high melt viscosity UHMWPE with CNF was feasible by optimizing the melt blending processing condition in triple screw kneading extruder, which resulted in improved stiffness, a contributing factor for wear resistance.

19 November 2024 in Biocatalysis and Agricultural Biotechnology
Verified
Journal Article
Closed access
NINur Liyana Mohd Izan
Nur Liyana Mohd Izan
EBEzyana Kamal Bahrin
Ezyana Kamal Bahrin
MYMohd Zulkhairi Mohd Yusoff
Mohd Zulkhairi Mohd Yusoff
KSKhanom Simarani
Khanom Simarani
NSNur Sharmila Sharip
Nur Sharmila Sharip
HAHidayah Ariffin
Hidayah Ariffin