paul chesler

Dr. paul chesler

Institute of Physical Chemistry Ilie Murgulescu of Romanian Academy, Bucharest, Bucureşti, Romania
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2022 in Catalysts
Verified
Journal Article
Open access
PDF file
VBVeronica Bratan
Veronica Bratan
Anca VasileAnca Vasile
Anca Vasile
paul cheslerpaul chesler
paul chesler
CRISTIAN HornoiuCRISTIAN Hornoiu
CRISTIAN Hornoiu
Volatile organic compound (VOC) abatement has become imperative nowadays due to their harmful effect on human health and on the environment. Catalytic oxidation has appeared as an innovative and promising approach, as the pollutants can be totally oxidized at moderate operating temperatures under 500 °C. The most active single oxides in the total oxidation of hydrocarbons have been shown to be manganese and cobalt oxides. The main factors affecting the catalytic performances of several metal-oxide catalysts, including CoOx and MnOx, in relation to the total oxidation of hydrocarbons have been reviewed. The influence of these factors is directly related to the Mars–van Krevelen mechanism, which is known to be applied in the case of the oxidation of VOCs in general and hydrocarbons in particular, using transitional metal oxides as catalysts. The catalytic behaviors of the studied oxides could be closely related to their redox properties, their nonstoichiometric, defective structure, and their lattice oxygen mobility. The control of the structural and textural properties of the studied metal oxides, such as specific surface area and specific morphology, plays an important role in catalytic applications. A fundamental challenge in the development of efficient and low-cost catalysts is to choose the criteria for selecting them. Therefore, this research could be useful for tailoring advanced and high-performance catalysts for the total oxidation of VOCs.

1 February 2016 in Materials Science in Semiconductor Processing
Verified
Journal Article
Closed access
MDM. Duta
M. Duta
LPL. Predoana
L. Predoana
JCJ.M. Calderon-Moreno
J.M. Calderon-Moreno
SPSilviu Preda
Silviu Preda
Mihai AnastasescuMihai Anastasescu
Mihai Anastasescu
Mariuca GartnerMariuca Gartner
Mariuca Gartner

22 December 2016 in Beilstein Journal of Nanotechnology
Verified
Journal Article
Open access
PDF file
paul cheslerpaul chesler
paul chesler
CHCristian Hornoiu
Cristian Hornoiu
SMSusana Mihaiu
Susana Mihaiu
CVCristina Vladut
Cristina Vladut
JMJose Maria Calderon Moreno
Jose Maria Calderon Moreno
Mariuca GartnerMariuca Gartner
Mariuca Gartner
A series of SnO2–ZnO composite nanostructured (thin) films with different amounts of SnO2 (from 0 to 50 wt %) was prepared and deposited on a miniaturized porous alumina transducer using the sol–gel and dip coating method. The transducer, developed by our research group, contains Au interdigital electrodes on one side and a Pt heater on the other side. The sensing films were characterized using SEM and AFM techniques. Highly toxic and flammable gases (CO, CO2, CH4, and C3H8) were tested under lab conditions (carrier gas was dry air) using a special gas sensing cell developed by our research group. The gas concentrations varied between 5 and 2000 ppm and the optimum working temperatures were in the range of 210–300 °C. It was found that the sensing performance was influenced by the amount of oxide components present in the composite material. Improved sensing performance was achieved for the ZnO (98 wt %)–SnO2 (2 wt %) composite as compared to the sensors containing only the pristine oxides. The sensor response, cross-response and recovery characteristics of the analyzed materials are reported. The high sensitivity (RS = 1.21) to low amounts of CO (5 ppm) was reported for the sensor containing a composite sensitive film with ZnO (98 wt %)–SnO2 (2 wt %). This sensor response to CO was five times higher as compared to its response to CO2, CH4, and C3H8, thus the sensor is considered to be selective for CO under these test conditions.

1 May 2017 in Ultrasonics Sonochemistry
Verified
Journal Article
Closed access
OCOana Carp
Oana Carp
ATAlina Tirsoaga
Alina Tirsoaga
RERamona Ene
Ramona Ene
AIAdelina Ianculescu
Adelina Ianculescu
RNRaluca F. Negrea
Raluca F. Negrea
RBRuxandra Birjega
Ruxandra Birjega

1 October 2017 in Sensors and Actuators B: Chemical
Verified
Journal Article
Closed access
BFBogdan Firtat
Bogdan Firtat
CMCarmen Moldovan
Carmen Moldovan
CBCostin Brasoveanu
Costin Brasoveanu
GMGeorge Muscalu
George Muscalu
Mariuca GartnerMariuca Gartner
Mariuca Gartner
ISIon Stan
Ion Stan

29 January 2023 in Chemosensors
Verified
Journal Article
Open access
PDF file
paul cheslerpaul chesler
paul chesler
CRISTIAN HornoiuCRISTIAN Hornoiu
CRISTIAN Hornoiu
The identification of an unknown gaseous species or the composition of a gaseous mixture can be performed using various experimental techniques such as: mass spectrometry, chromatography, nuclear magnetic resonance (NMR), infrared (IR), X-Rays, or by combining these analytical techniques (in automated analyzers). Unfortunately, these techniques use highly expensive equipment and require the use of qualified personnel. Using gas sensors is a viable and inexpensive alternative. The most commonly used sensors in the field are resistive type chemosensors (chemiresistors), due to their simple detection mechanism and low manufacturing costs. The detection principle of these sensors is based on the catalytic reaction between the sensitive material of the sensor and the target gas. This reaction occurs with the release or consumption of electrons, influencing the overall electrical resistance of the sensor. This review describes various MOX-based chemiresistors, which contain different types of sensitive substrates, such as powders, pellets or films, as well as a clear tendency towards sensor miniaturization and the constant improvement of the fabrication techniques towards greener and more cost-effective synthesis routes over time. The goal of this research was to obtain sensors with high 3S parameters (sensitivity, selectivity, and stability), that can be mass-produced and implemented on a wide scale.