Piotr J. Chrzan

Prof. Piotr J. Chrzan

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 January 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MTMarek Turzynski
Marek Turzynski
PCPiotr J. Chrzan
Piotr J. Chrzan
In the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction machine was equipped with hybrid ceramic bearings and an insulated clutch to measure the shaft-to-frame bearing voltage and the shaft-grounding current. Experimental tests of the PQRDCLI confirm significant reduction of common mode voltage and shaft-to-frame bearing voltage at dc-link zero voltage notches. By controlling the output voltage slopes, the shaft-grounding brush current and the ground leakage current are also reduced. The efficiency measurement and evaluation of the proposed topology, as compared with a two-level hard switched inverter, reveal comparable efficiency of around 95% and indicate loss distributions in both inverters.

23 May 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
PDPawel B. Derkacz
Pawel B. Derkacz
Jean-Luc SchanenJean-Luc Schanen
Jean-Luc Schanen
PJPierre-Olivier Jeannin
Pierre-Olivier Jeannin
PCPiotr J. Chrzan
Piotr J. Chrzan
PMPiotr Musznicki
Piotr Musznicki
MPMickael Petit
Mickael Petit
This article presents local shielding techniques applied to a half-bridge inverter leg with the aim to reduce the common-mode (CM) current noise at converter’s dc input. The research study is conducted for 650-V enhancement mode Gallium Nitride power transistor switches. Main contributors of parasitic capacitances referred to the inverter-leg middle point node are identified. Then, shielding solutions are proposed to reduce the CM current emission by these capacitances. Respecting the precautions concerning the isolation of CM currents of the half-bridge inverter leg, the electromagnetic compatibility measurement setup is developed. Experimental step-by-step addition of local shielding copper layers to different contributors of middle point capacitance shows progressive attenuation of CM noise spectra.

1 September 2017
Verified
Conference Paper
Closed access
MTMarek Turzynski
Marek Turzynski
PCPiotr J. Chrzan
Piotr J. Chrzan
MKMaciej Kolincio
Maciej Kolincio
SBStefan Burkiewicz
Stefan Burkiewicz

15 February 2019 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
MKMaciej Kolincio
Maciej Kolincio
PCPiotr J. Chrzan
Piotr J. Chrzan
PMPiotr Musznicki
Piotr Musznicki

13 April 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
PDPawel B. Derkacz
Pawel B. Derkacz
PMPiotr Musznicki
Piotr Musznicki
PCPiotr J. Chrzan
Piotr J. Chrzan
A dc-dc buck converter using gallium nitride (GaN) high electron mobility transistors (HEMT) is experimentally investigated at the discontinuous current mode (DCM) and at the triangular current mode (TCM) operation. The paper objective is to specify the power conversion efficiency and attenuation of common mode (CM) and differential mode (DM) noise voltage, measured at the line impedance stabilization network (LISN) for compared control strategies. Zero voltage switching achieved for the TCM operation improves efficiency with reference to the DCM operation. However, significant attenuation of electromagnetic interference (EMI) spectra is obtained for TCM operation with capacitive snubber. Sizing of capacitor snubber dependent on parasitic inductances of commutation circuit and rapid switching of GaN HEMTs are illustrated.

22 July 2021 in Energies
Verified
Journal Article
Open access
PDF file
PMPiotr Musznicki
Piotr Musznicki
PDPawel B. Derkacz
Pawel B. Derkacz
PCPiotr J. Chrzan
Piotr J. Chrzan
The general wideband modeling method of the power converter is presented on the example of DC-DC buck converter with GaN High Electron Mobility Transistors (HEMT). The models of all basic and parasitic components are briefly described. The two methods of Printed Circuit Board (PCB) layout parameter extraction are presented. The results of simulation in Saber@Sketch simulation software and measurements are compared. Next, the model of the converter is reduced to obtain one lumped inductance of the input filter PCB for the analytical prediction of transistor turn-off ringing frequency and overvoltage. The practical use of the model is presented for sizing optimal capacitance of snubber.