Mickael Petit

Mickael Petit

Auto-generated profile, based on publicly available information

Mickael Petit

ENS Paris-Saclay, CNRS, Universit Paris-Saclay, SATIE, Gif-sur-Yvette, France

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2015 in Microelectronics Reliability
Verified
Journal Article
Closed access
CCCheng Chen
Cheng Chen
DLDenis Labrousse
Denis Labrousse
SLStéphane Lefebvre
Stéphane Lefebvre
MPMickael Petit
Mickael Petit
CBCyril Buttay
Cyril Buttay
HMHervé Morel
Hervé Morel

11 March 2013 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
MTMansour Tawk
Mansour Tawk
YAYvan Avenas
Yvan Avenas
AKAfef Kedous-Lebouc
Afef Kedous-Lebouc
MPMickael Petit
Mickael Petit
Thermal management became a limiting factor in the development of high-power electronic devices, and new methods of cooling are required. Therefore, the use of liquid gallium alloys, whose thermal conductivity (approximately 28 W/m/K) is 40 times greater than thermal conductivity of water, is introduced. In the first part of this paper, we present a numerical modeling and an experimental study of a mini-channel liquid metal cooler. In these experiments, the working fluid is moved via an electromagnetic pump. Numerical and experimental results are compared. Then, a numerical study dealing with the influence of the thermal conductivity of the cooler material is conducted, and a discussion on the use of classical convective heat transfer correlations is presented. In the last part, a numerical study of the cooling of a silicon chip is carried out. The cooling capacity of the liquid metal is compared with that of the water cooling, and very attractive results are obtained. The concept discussed in this paper is expected to provide a powerful cooling strategy for high-power-density electronic devices.

23 May 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
PDPawel B. Derkacz
Pawel B. Derkacz
Jean-Luc SchanenJean-Luc Schanen
Jean-Luc Schanen
PJPierre-Olivier Jeannin
Pierre-Olivier Jeannin
PCPiotr J. Chrzan
Piotr J. Chrzan
PMPiotr Musznicki
Piotr Musznicki
MPMickael Petit
Mickael Petit
This article presents local shielding techniques applied to a half-bridge inverter leg with the aim to reduce the common-mode (CM) current noise at converter’s dc input. The research study is conducted for 650-V enhancement mode Gallium Nitride power transistor switches. Main contributors of parasitic capacitances referred to the inverter-leg middle point node are identified. Then, shielding solutions are proposed to reduce the CM current emission by these capacitances. Respecting the precautions concerning the isolation of CM currents of the half-bridge inverter leg, the electromagnetic compatibility measurement setup is developed. Experimental step-by-step addition of local shielding copper layers to different contributors of middle point capacitance shows progressive attenuation of CM noise spectra.

1 August 2017 in Applied Thermal Engineering
Verified
Journal Article
Closed access
WCWahid Cherief
Wahid Cherief
YAYvan Avenas
Yvan Avenas
SFSébastien Ferrouillat
Sébastien Ferrouillat
AKAfef Kedous-Lebouc
Afef Kedous-Lebouc
LJLaurent Jossic
Laurent Jossic
MPMickael Petit
Mickael Petit

1 September 2017 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
YPYoann Pascal
Yoann Pascal
AAAmar Abdedaim
Amar Abdedaim
DLDenis Labrousse
Denis Labrousse
MPMickael Petit
Mickael Petit
SLStephane Lefebvre
Stephane Lefebvre
FCFrancois Costa
Francois Costa
The proposed innovative manufacturing process-described in detail-uses metal foam to create a pressed contact between the top side of a printed circuit board-embedded power die and the rest of the circuit. Initial prototypes were constructed using diodes with die dimensions of 4 mm × 6.35 mm. The prototypes were electrically characterized: the chip and contact dc and ac impedance values were measured and compared with those obtained for conventional packaging that uses bond wires. The electrical impedance of the prototypes was found to be similar to that of a state-of-the-art industrial package. Moreover, the proposed process is simple and cost-effective. Although the results presented in this letter are promising, further research is necessary to fully assess the benefits and limitations of the process.

9 February 2017
Verified
Conference Paper
Closed access
HDHocine Daou
Hocine Daou
MAMenouar Ameziani
Menouar Ameziani
DLDominique Lhotellier
Dominique Lhotellier
FCFrancois Costa
Francois Costa
MPMickael Petit
Mickael Petit
ELEric Laboure
Eric Laboure
The layout of power modules is one of the key points in power module design, especially for high power densities, where couplings are increased. Stray inductances cause various problems in switching devices and should be minimized at an early design stage to avoid later required countermeasures and redesign after the device prototype has been built. In this paper, using Ansys® Q3D® Extractor, electromagnetic simulation is carried out to extract and evaluate the inductive and resistive parasitics of one phase of a three-phase automotive inverter module with rating of 650 V–400 A. The purpose is to develop and verily the electrical model including parasitic parameters for the studied phase-leg operating as a chopper. The switching behavior of the studied structure is analyzed based on Ansys® Simplorer® simulation, and a dynamic electrical model is carried out. Experimental test measurements are performed. The comparison between the simulation models and the experimental data is reported and conclusions are made.