Present work focusses on investigating the effect of process parameters such as feed rate and spindle speed on quality characteristics of the hole, i.e., surface roughness (Ra) and circularity at entry and exit in the drilling of aluminium (Al) 6061 reinforced with different volume fraction of silicon nitride (Si3N4). Optimum parameters for Ra and circularity of hole at entry and exit are obtained as feed rate at 0.125 mm/rev, spindle speed at 300 rpm, diameter of drill at 8 mm, and % Vol. of Si3N4 at 5%. Using Analysis of Variance (ANOVA), we observed that spindle speed is the most influential parameter followed by feed rate.
The utilization of composite materials in structural components has been on the rise in the aerospace, automotive, and marine industries. Although these materials offer numerous benefits, they can be damaged by various sources, such as low-velocity drop-weight impacts. Debris on a runway or tools falling onto composites can cause this type of impact, which has led to extensive research on crashworthiness and impact damage assessment. This study aimed to assess the response of woven E-glass/epoxy composite laminates under low-velocity drop-weight impacts. Tests were conducted using experimental methods and numerical simulations with a drop-weight impact-testing machine and the explicit finite element software LS-DYNA. The experimental tests were performed according to ASTM standards, with varied magnitudes of initial impact energy ranging from 7.85 J to 23.54 J and a specimen thickness of 4 mm. Force–time, energy–time, and force–displacement histories, obtained through the experiments and numerical analyses along with images of the damaged specimens, were examined. The effective stress contours are also illustrated to gain a deeper comprehension of the stress distribution in the laminates. The findings demonstrated that the impact energy significantly influences the impact response of the specimens, and both the experimental and numerical analyses yielded similar results, validating the modeling approach for the impact problem in composite materials. The study provides insight into the damage mechanism of woven E-glass/epoxy composite laminates under drop-weight impacts and is expected to contribute to a better understanding of their response in low-velocity drop-weight impact events.
Flow rate measurement is a challenging task in the industry as there is no general-purpose measuring instrument for all appliances. However, orifice plates with multiple holes can be employed to measure the flow rate accurately. A computational fluid dynamics (CFD)-based numerical study was conducted to investigate the flow separation characteristics caused by the flow of water in multiple-hole orifice plates using ANSYS FLUENT R15.0 software. The study included single- and multiple-hole orifice plates, with orifices with a 36% area ratio, an equivalent diameter ratio (β-ratio) of 0.6, and hole number configurations of 1H, 4H, 9H, 16H, and 25H. The discharge coefficient for flow through multiple-hole orifices was obtained and compared for holes distributed in circular and square configurations. The significant parameters considered for the analysis were the hole number, distribution of holes, pressure drop, and reattachment points. A k-ε turbulence model was employed to study velocity fields, reattachment length, and discharge coefficient. We discuss the effects of hole numbers and their allocation on the reattachment length and discharge coefficient. Results are presented in the form of pressure variation comparisons, downstream recovery distance plots, recirculation zone plots, and percentage change in the coefficient of discharge. The study revealed that the number of holes in the plate significantly affects the pressure drop across the plate, the recirculation zone, and the orifice’s discharge coefficient.
The successful joining of two dissimilar materials has a wide range of applications like in the nuclear sector, oil refinery plants, heat exchangers, and chemical processing equipments. Effective welding of dissimilar material is need of the hour in recent times because of its unique mechanical properties. In this work, mechanical properties of SS 316L and IS 2062 E250A dissimilar materials welded by Tungsten inert gas welding is studied. Also, the relationship between the welding parameter and the mechanical properties is achieved by correlating the results of experiment and finite element analysis. Specimens were prepared based on the Taguchi L9 orthogonal array and thereafter finite element analysis, tensile and hardness test is carried out. The results obtained from these methods almost go hand in hand thereby giving out the parameters responsible for superior tensile strength and hardness. Apart from that the correlation gives an idea about the parameter relation to obtain good weld.