Present work focusses on investigating the effect of process parameters such as feed rate and spindle speed on quality characteristics of the hole, i.e., surface roughness (Ra) and circularity at entry and exit in the drilling of aluminium (Al) 6061 reinforced with different volume fraction of silicon nitride (Si3N4). Optimum parameters for Ra and circularity of hole at entry and exit are obtained as feed rate at 0.125 mm/rev, spindle speed at 300 rpm, diameter of drill at 8 mm, and % Vol. of Si3N4 at 5%. Using Analysis of Variance (ANOVA), we observed that spindle speed is the most influential parameter followed by feed rate.
India imports fossil fuels to meet its energy needs, and the need is anticipated to increase over the coming years. The constant usage of crude fuel will initiate its depletion in due course, necessitating the hunt for substitute fuels. One of the most promising alternatives to fossil fuels is determined to be biofuels. Fuels made from second-generation feedstocks, particularly non-edible oils, may change the game in this situation. The use of Simarouba non-edible oil as a substitute for diesel in common rail direct injection (CRDI) engines is the subject of the current piece of research. Running a CRDI engine with Simarouba biodiesel blends may not be suitable under the same operating conditions as running a diesel engine. To optimize performance, the ideal conditions for operating a CRDI engine with Simarouba biodiesel mixes needs to be discovered. The control settings in this study that affect the engine’s performance viz., fuel temperature (FPT), fuel injection pressure (IP), and injection time (IT) are designed using the Taguchi technique. Under full load conditions of 12 kg, for the biodiesel blends viz., SB5, SB10, and SB20, studies were conducted using the Taguchi L9 orthogonal array (OA). Through experimentation, performance and emission responses were obtained. For analysis, six engine responses were considered. The analysis shows that each response is uniquely impacted by the engine control parameters. Therefore, it might be challenging to pinpoint the ideal circumstances that would improve performance and lower emissions. Thus, this presents an example of a multi-response optimization problem. For this reason, multiple response optimization uses Taguchi-Grey Relational Analysis (TGRA). According to TGRA, the ideal settings to increase engine performance while using Simarouba biodiesel blends as fuel are an FPT of 40 °C, an IT of 21° bTDC, and an IP of 600 bar.
13 August 2025 in Journal of Workplace Behavioral Health
A comparative study of the effect of co-sputtering specifically magnetron sputtering process input factors on surface roughness of W and Al2O3 thin film developed on the SS304 and Copper(Cu) substrates in the argon atmosphere. The input parameters have been varied based on the Design of Experiments specifically Center Composite Design experimental plan. Atomic Force microscope has been used to determine the average surface roughness in nanometer of all the samples as per experimental combinations. By using ANOVA method, the effect of factors on roughness and regression model have been developed, which express degree to input parameter can effect on the surface roughness. Analysis of surface roughness of W and Al2O3 thin film developed above said different substrates have been presented.
This research examines the impact of Computer-Aided Engineering Drawing (CAED) programs on the development of perceived interdisciplinary competency in engineering and computer science courses through Structural Equation Modeling (SEM), focusing on two mediating mechanisms: student attitudes toward CAED programs and the learning process within a supportive institutional environment. The structural equation model explained a substantial proportion of the variance in perceived competency (R² = 0.744) and indicated that both attitudes (β = 0.787) and learning experience (β = 0.782) were considerably influenced by CAED program design. Competency mediated by student attitudes (β = 0.229) and by learning experience (β = 0.370) had significant indirect effects, and the institutional context itself positively impacted competency (β = 0.327), likely reflecting the resources available and the promotion of interdisciplinary teamwork. Overall, the results highlight the significance of designing CAED programs in accordance with industry requirements, alongside active learning methods that foster positive student perceptions, and the importance of robust institutional support systems that equip students with the competencies required in modern engineering practice. The study is limited by its cross-sectional nature and single-institution sample. Future research can examine the long-term effects of these relationships, investigate how institutional variables may moderate them, and test the validity of the relationships across multiple institutions.