The purpose of this research is to develop an efficient single-phase grid-connected PV system using a better performing asymmetrical multilevel inverter (AMI). Circuit component reduction, harmonic reduction, and grid integration are critical criteria for better inverter efficiency. The proposed inverter’s optimized topology requires seven unidirectional switches, three symmetric dc sources, and three diodes to produce an asymmetric fifteen level output; whereas, the same configuration will generate 7, 11, and 15-level output with an appropriate choice of dc source magnitudes. It is possible to reduce inverter losses and boost efficiency by decreasing the number of switches used. The integration of an asymmetric 15-level inverter with a grid-connected solar photovoltaic system is discussed in this article. A grid-connected solar photovoltaic (GCSPV) system is modelled and simulated using an asymmetric 15-level inverter. The dc sources of the 15-level inverter are replaced with PV sources. The results were analyzed with different operating temperatures and solar irradiance conditions. The GCSPV system is controlled by a closed-loop control system using Particle Swarm Optimization (PSO), Harris Hawk Optimization (HHO), and Hybrid Particle Swarm Optimization-Genetic Algorithm (PSOGA) based Proportional plus Integral (PI) controllers. Grid voltage, grid current, grid power, and total harmonic distortion (THD) of grid currents were analyzed. The performance of the 15-level asymmetric inverter was evaluated by comparing the THD of the grid current and the efficiency of the grid-connected photovoltaic system.
Recent trends in the photovoltaic (PV) technology industry are moving towards utilizing bifacial PV panels. Unlike traditional PV panels, bifacial PV panels can yield energy from both sides of the panel. Manufacturers specify that bifacial PV panels can harness up to 30% more energy than traditional PV panels. Hence, bifacial PV panels are becoming a common approach at low solar irradiance conditions to yield more energy. However, a bifacial PV panel increases PV inverter loading. The PV inverter is the most unreliable component in the entire PV system. This results in a negative impact on PV system reliability and cost. Hence, it is necessary to anticipate the inverter’s reliability when used in bifacial PV panels. This paper analyzes the reliability, i.e., lifetime, of PV inverters, considering both monofacial and bifacial PV panels for the analysis. Results showed that the increase in bifacial energy yield could significantly affect PV inverter reliability performance, especially in locations where the average mission profile is relatively high.
Energy harnessing from renewable energy sources has become more flexible with power electronic technologies. Recent advancements in power electronic technologies achieve converter efficiency higher than 98%. Today, reliable power electronic devices are needed to design a PV-based energy converter (inverter) to reduce the risk of failure and maintenance costs during operation. Wide-bandgap SiC devices are becoming more common in power electronic converters. These devices are designed to reduce switching loss and improve the efficiency of the system. Nevertheless, the cost of SiC devices is a major concern. Hence, to improve the reliability of the PV inverter while considering the economic aspects, this paper develops a highly reliable PV inverter with a hybrid Si/SiC power module that consists of a Si-IGBT with a SiC anti-parallel diode. A test case of a 3 kW PV inverter is considered for reliability analysis. The loading of the PV inverter is done under uncertain environmental conditions by considering the yearly Mission Profile (MP) data related to Ambient Temperature (AT) and Solar Irradiance (SI) at the India and Denmark locations. The effectiveness of the proposed hybrid Si/SiC power module is tested by comparing it with a conventional IGBT power module. The results showcase the marked improvement in PV inverter reliability with the proposed hybrid power module.
The rapid emergence and evolution of renewable energy sources such as solar energy has become a vital component of the global effort to meet the energy needs of the future. The major concerns for continuous solar photovoltaic (PV) generation are degradation rate, hot spots. These factors lead to the negative impact on PV mismatch losses, fill factor, maximum power and efficiency. To improve the performance of PV system, the simplest solution is PV panel configuration hence in this paper spider web tie (SWT) based PV Panel configuration in proposed. The proposed configuration is implemented on KC200GT PV Panel of 5×5 size PV panels considering degradation rate, hot spot. The performance of SWT configuration is compared with series-parallel (SP), bridge-link (BL), triple tied (TT), and photovoltaic (PV) panel configurations and performance parameters such as Vmp, Imp, Pmp, Voc, Isc. FF, ∆Pml, and η are calculated in all the cases. In all the cases the proposed SWT configuration exhibited the improved performance.
17 October 2026 in Innovative Infrastructure Solutions