Foot pressure measurement plays an essential role in healthcare applications, clinical rehabilitation, sports training and pedestrian navigation. Among various foot pressure measurement techniques, in-shoe sensors are flexible and can measure the pressure distribution accurately. In this paper, we describe the design and characterization of flexible and low-cost multi-walled carbon nanotubes (MWCNT)/Polydimethylsiloxane (PDMS) based pressure sensors for foot pressure monitoring. The sensors have excellent electrical and mechanical properties an show a stable response at constant pressure loadings for over 5000 cycles. They have a high sensitivity of 4.4 k/kPa and the hysteresis effect corresponds to an energy loss of less than 1.7%. The measurement deviation is of maximally 0.13% relative to the maximal relative resistance. The sensors have a measurement range of up to 330 kPa. The experimental investigations show that the sensors have repeatable responses at different pressure loading rates (5 N/s to 50 N/s). In this paper, we focus on the demonstration of the functionality of an in-sole based on MWCNT/PDMS nanocomposite pressure sensors, weighing approx. 9.46 g, by investigating the foot pressure distribution while walking and standing. The foot pressure distribution was investigated by measuring the resistance changes of the pressure sensors for a person while walking and standing. The results show that pressure distribution is higher in the forefoot and the heel while standing in a normal position. The foot pressure distribution is transferred from the heel to the entire foot and further transferred to the forefoot during the first instance of the gait cycle.
In this report, we demonstrate the capability of electrochemically deposited copper (Cu) nanoparticles on electrochemically reduced graphene oxide (ERGO)‐multiwalled carbon nanotubes (MWCNT) composite on screen printed carbon electrodes (SPCE) for electrochemical detection of nitrate. Prior to the detection, extensive fundamental investigations on the electrochemical reduction of GO on SPCE and role of MWCNT in the reduction process and the degree of reduction have been carried out which has not been previously reported. Profiting from the complementary information obtained from electrochemical impedance spectroscopy, Raman spectroscopy, and cyclic voltammetry (CV), the role of MWCNT and optimal number of scans in CV (15 scans) for the reduction was obtained. The determination of nitrate on Cu/ERGO‐MWCNT/SPCE was performed by square wave voltammetry and shows a wide linear range from 10 to 750 μM and low limit of detection of 3.3 μM, thereby enhancing the applicability of the developed electrode in the regions of low and high concentrations as well. The electrode was tested in tap water and the analytical capability was compared using F‐test and matrix effect (4.8 %), which highlights excellent analytical ability of the Cu/ERGO‐MWCNT modified electrodes to detect nitrate.
Over the past few decades, there has been a growing trend in designing multifunctional materials and integrating various functions into a single component structure without defects. This research addresses the contemporary demand for integrating multiple functions seamlessly into thermoplastic laminate structures. Focusing on NiTi-based shape memory alloys (SMAs), renowned for their potential in introducing functionalities like strain measurement and shape change, this study explores diverse surface treatments for SMA wires. Techniques such as thermal oxidation, plasma treatment, chemical activation, silanization, and adhesion promoter coatings are investigated. The integration of NiTi SMA into Glass Fiber-Reinforced Polymer (GFRP) laminates is pursued to enable multifunctional properties. The primary objective is to evaluate the influence of these surface treatments on surface characteristics, including roughness, phase changes, and mechanical properties. Microstructural, analytical, and in situ mechanical characterizations are conducted on both raw and treated SMA wires. The subsequent incorporation of SMA wires after characterization into GFRP laminates, utilizing hot-press technology, allows for the determination of interfacial adhesion strength through pull-out tensile tests.
Tungsten fiber-reinforced tungsten (Wf/W) composites are being developed to improve the intrinsic brittleness of tungsten. In these composites, engineered fiber/matrix interfaces are crucial in order to realize toughening mechanisms. For such a purpose, yttria (Y2O3), being one of the suitable interface materials, could be realized through different coating techniques. In this study, the deposition of thin films of yttria on a 150 µm tungsten wire by physical and chemical vapor deposition (PVD and CVD) techniques is comparatively investigated. Although fabrication of yttria is feasible through both CVD and PVD routes, certain coating conditions such as temperature, growth rate, oxidation of Wf, etc., decide the qualitative nature of a coating to a particular extent. In the case of PVD, the oxidation of Wf is highly reduced compared to the WO3 formation in high-temperature CVD coating processes. Yttria-coated tungsten fibers are examined comprehensively to characterize their microstructure, phase, and chemical composition using SEM, XRD, and Raman spectroscopy techniques, respectively.
Since lightweight design and construction safety is a crucial element in different sectors of industry, the use of SMA wires in composites could improve the monitoring and adjustment of mechanical properties starting from the product development process through to field use. This work shows how embedded SMA wires can lead to a better understanding of applied forces to a composite structure made of GFRP laminates. To achieve this, different methods will be addressed. Besides mechanical testing of the GFRP-samples with embedded SMA wires, NDT-methods like active thermography, high-frequency ultrasonic testing, and computer tomography are used to detect the SMA wires, whereby thermography and computer tomography are best suited. In this study, the location and the amount of the applied force on GFRP composites with embedded SMA wires could be characterized with relative resistance changes. It is shown that SMA wires with a diameter of 250 µm are preferred to wires with a diameter of 100 µm due to production process and better performance under load (4N force plateau for 100 µm in contrast to 25N force plateau for 250 µm wires). Furthermore, Young’s modulus of the GFRP composites with embedded SMA wires was measured and is similar for various samples with 30.8 GPa on average.
9 January 2026 in Journal of Materials Research and Technology