Salvador Magdaleno Adame

Mr. Salvador Magdaleno Adame

Magnetic Instrumentation
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2019 in Machines
Verified
Journal Article
Open access
PDF file
VKVladimir Kuptsov
Vladimir Kuptsov
PFPoria Fajri
Poria Fajri
ATAndrzej Trzynadlowski
Andrzej Trzynadlowski
GZGuoliang Zhang
Guoliang Zhang
SASalvador Magdaleno Adame
Salvador Magdaleno Adame
This article presents a new and powerful freeware software called MotorAnalysis-PM and discusses its application in electromagnetic design and analysis of permanent magnet (PM) motors for the electric vehicle (EV) industry. This new PM motor software utilizes both finite element (FE) and analytical methods to speed up the analysis and design process of PM motors significantly. The analysis and design methodology using MotorAnalysis-PM is presented and discussed for a 50 kW PM motor utilized in a commercial EV. To validate the accuracy of the software, the numerical results obtained from the PM motor design and analysis tool are compared with experimental results. The numerical and experimental results validate the flexibility of this software in achieving accurate motor design with short design times which is of great interest to EV and PM motor manufacturers.

1 December 2019 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
SASalvador Magdaleno Adame
Salvador Magdaleno Adame
GCG. J. Cunningham
G. J. Cunningham
DMD. Miller
D. Miller
SOS. O'BRien
S. O'BRien

11 February 2022 in Machines
Verified
Journal Article
Open access
PDF file
VKVladimir Kuptsov
Vladimir Kuptsov
PFPoria Fajri
Poria Fajri
MRMd Rasheduzzaman
Md Rasheduzzaman
SASalvador Magdaleno Adame
Salvador Magdaleno Adame
KHKonstantin Hadziristic
Konstantin Hadziristic
This article presents a new method for combined levitation and propulsion control in maglev/Hyperloop systems by selectively applying AC and DC modes of operation to a group of asymmetric double-sided linear induction motors (ADSLIMs). Although adjusting the AC current magnitude of lower and upper primary windings in ADSLIMs allows simultaneous control of thrust and lift forces, the limitation of this current balancing technique prohibits them from producing a high lift force while operating with low thrust force. To overcome this limitation and to simultaneously control the thrust and lift forces of the ADSLIMs with high efficiency under different operating conditions, a combination of AC and DC modes of operation is proposed. AC mode of operation consists of feeding different AC current amplitudes to the upper and lower ADSLIM primary windings to produce and control the required thrust and lift forces. The DC mode of operation consists of controlling one or several ADSLIMs to operate with DC excitation to realize the desired lift force at lower thrusts which otherwise cannot be achieved by operating in AC mode alone. The concept of the new combined control strategy is studied using two-dimensional finite element (FE) electromagnetic simulations and compared with an Inductrack permanent magnet (PM) based passive magnetic levitation system.

10 November 2021
Verified
Conference Paper
Closed access
SASalvador Magdaleno Adame
Salvador Magdaleno Adame
RORodrigo Ocon-Valdez
Rodrigo Ocon-Valdez
DJDavid Juarez-Aguilar
David Juarez-Aguilar
ECElizabeth Cortina-Gonzalez
Elizabeth Cortina-Gonzalez
JOJuan C. Olivares-Glavan
Juan C. Olivares-Glavan
This paper presents an electromagnetic analysis of the bevel edge technique (BET) employed to reduce core losses in high voltage (HV) gapped-core shunt reactors. The authors analyzed this BET employing three-dimensional (3-D) finite element (FE) simulations. The magnetic anisotropy and the magnetic nonlinear properties of the grain-oriented electrical steel are considered in the FE simulations. The authors validated their FE simulations by computing the core losses in a real 5 MVAr three-phase shunt reactor without BET and comparing them with the core losses measured in the laboratory. Once validating the FE simulations of the HV shunt reactor without BET, the authors analyzed the core losses in the same HV shunt reactor with BET. In addition, the authors analyzed the core loss effect produced by the bevel edge length in two real HV shunt reactors: a 25 MVAr single-phase shunt reactor and in the original 5 MVAr three-phase shunt reactor. Finally, the authors analyzed the bevel edge angle effect on the core losses of the 5 MVAr three-phase shunt reactor. Authors demonstrated and confirmed that the BET helps to reduce the core losses in HV shunt reactors. Finally, the authors concluded that the bevel edge length and the bevel edge angle have a slight impact on the core losses of the HV shunt reactors.

4 March 2019 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
SASalvador Magdaleno Adame
Salvador Magdaleno Adame
TKThemistoklis D. Kefalas
Themistoklis D. Kefalas
This paper presents a magnetic safety evaluation of the static magnetic field produced by magnetic floors with permanent magnet properties utilized in the construction industry. The magnetic floors analyzed in this paper are composed by a concentration of 85% of isotropic strontium (Sr) ferrite powder mixed with chlorinated polyethylene. The magnetic floors are magnetized and tested in the laboratory to measure the magnetic field levels in different regions of the magnetic floors and magnetic subfloors. Finite-element (FE) simulations are carried out to compute the magnetic field produced by magnetic floors. The numerical results and laboratory tests are compared and analyzed. Values of the magnetic field between 2 and 50 mT are computed and measured in different regions of magnetic floors. Finally, the static magnetic field levels obtained in the magnetic floors are compared with the permitted magnetic field values for different electronic devices, pacemakers, and other common objects utilized by persons in buildings. The results obtained in this paper show that magnetic floors are safe, and they can be employed in buildings without putting in risk electronic devices or persons with pacemakers.