Metal corrosion is a serious technical and environmental problem that leads to significant economic losses and threatens the safety of infrastructure. Traditional methods of protecting metal structures are based on the use of chemical inhibitors, which are often toxic, poorly biodegradable and hazardous to human health and the environment. In response to these challenges, there is a growing interest in the development of “green” corrosion inhibitors - non-toxic, biodegradable and environmentally friendly substances derived from natural sources. This study examines the effectiveness of aqueous, alcoholic and water-alcohol plant extracts as an alternative to traditional corrosion inhibitors for the protection of 17GS steel in the NS4 model environment. Experimental studies have shown that the water-alcohol extract of Echinacea provides up to 69% protection of steel, the water extract of tea - up to 50%, while the effectiveness of eucalyptus oil was only 12%. The results obtained indicate a significant dependence of the protection efficiency on the type of plant material, extract concentration, exposure temperature, and duration of contact with the environment. Gravimetric analysis confirmed the formation of a dense protective adsorption-oligomeric film on the metal surface, which significantly reduces the corrosion rate and increases the polarization resistance of steel to 15 kΩ at a concentration of 40 ml/l. Microstructural analysis shows that the most effective compounds are those with aromatic structures and nitrogen-containing heterocycles that are able to form stable chemical bonds with the metal surface. A multivariate regression analysis of the dependence of steel corrosion resistance on exposure time, inhibitor concentration, and temperature was performed, which confirmed the significant impact of these factors on metal protection. The studies indicate that it is possible to optimize the composition of inhibitors by using combined herbal preparations and nanostructured additives to increase the duration and effectiveness of the protective effect. The results of this work open up new prospects for the development of environmentally friendly metal protection technologies that meet the concept of sustainable development and the principles of green chemistry. Further research should be focused on finding new sources of bioactive compounds, improving extraction methods, and in-depth study of the mechanisms of protective coatings formation.
1 November 2022 in Ecological Engineering & Environmental Technology
Application of sewage sludge (SS) as a fertilizer contributes to the intensity of Zn, Ga, Y, Zr, Rh, Pb uptake by Jerusalem artichoke plants. Also, the translocation coefficients of Zn, Sr, Y, Rh, Pb vary in a wide range of values, depending on the level of use of SS. Jerusalem artichoke culture...
At present stage of the development of the domestic gas production industry, the problem of increasing the volume of hydrocarbon production is extremely urgent for our state. In the dynamics, there is a significant increase in the volume of directional wells drilling. However, the drilling of such wells is associated with a number of problems. The main problems that may arise in this case are associated with insufficient stability of their bore, which in most cases leads to sticking of the drill string and a significant increase in material costs and production time for their elimination. Therefore, ensuring the integrity of the borehole walls during their drilling is a priority and extremely important problem in the system of measures aimed at improving the quality and improving the technical and economic indicators of their construction. The work is devoted to the improvement of the technology for preventing the destruction of the walls of directional wells, through the influence of technical, technological, mining, and geological factors on the change in the stress-strain state of the mass of the near-wellbore zone of the well. The production material on the sticking of the drill string was analyzed during the construction of wells in the Dnieper-Donets depression fields. It was found that the reasons for the loss of mobility of the drilling tool are mainly the violation of the integrity of the borehole walls as a result of caving and collapse of rocks, as well as the formation of keyseats on the borehole walls. Such complications arose, despite the observance of the operating and technological parameters, when deepening the well and recommendations for reducing keyseats on the walls of the well and preventing caving and collapse of rocks. The existing scientific and practical methods and approaches to prevent the loss of stability of the wellbore walls do not allow eliminating the indicated cause of complications, since the correct selection of the BHA, as well as the development of measures to reduce the intensity of capping and grooving, plays an important role. The paper proposes measures to prevent cavities and keyseats when drilling directional wells. The factors influencing the stability of the borehole walls in conditions prone to collapse and rock caving have been analyzed. The expediency of using baths for strengthening the walls of wells in clayey rocks has been established and substantiated. The formulation of a modified fuel-bitumen bath, the duration of which is 1.5÷5 times longer than that of a fuel-bitumen bath is proposed. A method is proposed for predicting intervals prone to complications associated with the loss of stability of the wellbore walls. According to industrial data, a technology has been proposed for installing a fuel-bitumen bath to prevent keyseats formation during well drilling. To eliminate the keyseats in the well, a bottom-hole assembly is proposed, which consists of stepped heavyweight drill pipes with simultaneous installation of tapered adapters at the transition points from a larger diameter of a drill string element to a smaller one and an eccentric carbide bit
30 April 2024 in Polish Journal of Environmental Studies
Studies carried out in the Transcarpathian region of Ukraine with the application of sewage sludge as fertilizer for Silphia prinosanolista showed that the use of 20-40 t/ha of fresh SS and composts based on it with cereal straw creates a different agrochemical background of alluvium, compared to the application of an equivalent norm of mineral fertilizers, and causes a change in the content of bioavailable forms of the main nutrients - nitrogen, phosphorus, and potassium in the soil layer 0-80 cm. Significant differences in the content of mineral and alkaline hydrolyzed nitrogen compounds in the upper layer of 0-40 cm of alluvium were established. Application of increasing (20-40 t/ha) rates of sewage sludge, as well as their composts with straw and a compensatory amount of mineral fertilizers, contributes to a reliable increase in the content of ammonium compared to the option without the application of fertilizers and the option with an equivalent dose of mineral fertilizers.