This paper presents a new investigation to detect various faults within the three-phase star and delta induction motors (IMs) using a frequency response analysis (FRA). In this regard, experimental measurements using FRA are performed on three IMs of ratings 1 HP, 3 HP and 5.5 HP in normal conditions, short-circuit fault (SC) and open-circuit fault (OC) conditions. The SC and OC faults are applied artificially between the turns (Turn-to-Turn), between the coils (Coil-to-Coil) and between the phases (Phase-to-Phase). The obtained measurements show that the star and delta IMs result in dissimilar FRA signatures for the normal and faulty windings. Various statistical indicators are used to quantify the deviations between the normal and faulty FRA signatures. The calculation is performed in three frequency ranges: low, middle and high ones, as the winding parameters including resistive, inductive and capacitive components dominate the frequency characteristics at different frequency ranges. Consequently, it is proposed that the boundaries for the used indicators facilitate fault identification and quantification.
21 April 2014 in IEEJ Transactions on Electrical and Electronic Engineering
In the present work, a hydrothermal reduction method is used to further enhance and optimize the pristine graphene aerogels (GAs) for supercapacitors. Three key variables (GO concentration, hydrothermal reduction temperature, and time) were optimized through the application of Taguchi design of experiments to the synthesis process. A total of nine experimental runs were conducted and repeated three times to confirm reproducibility. Electrochemical performances of the electrodes were evaluated by cyclic voltammetry (CV), galvanostatic discharge-charge (GCD), and electrochemical impedance spectroscopy (EIS). The optimized sample (5 mg/mL GO at 180 °C for 16 h) was further analyzed using morphological studies, including FIB-FESEM, Raman, XPS, and BET. The as-obtained 3D reduced graphene oxide network exhibited a maximum specific capacitance of 182.33 F/g at the current density of 0.2 A/g, corresponding to an energy density of 6.33 Wh/kg at a power density of 108.5 W/kg in a 6 M KOH electrolyte. This study systematically investigates the influence of hydrothermal reduction parameters on the energy density of graphene aerogel-based supercapacitors and pinpoints the best synthesis conditions. This also highlights the potential of pure GA as an electrode material, indicating opportunities for further enhancement through ongoing research and development.
This study explores the thermal performance of double-pass photovoltaic thermal (PVT) systems by investigating the influence of turn shape on heat transfer characteristics using computational fluid dynamics (CFD) simulations. The aim is to evaluate various turn shapes, including half-circle, triangle, half-hexagon, half-octagon, and box, to determine their impact on turbulent intensity, effective thermal conductivity, and outlet temperature in PVT systems. The investigation reveals significant variations in heat transfer efficiency among the different turn shapes, with the triangle-shaped turn demonstrating superior performance across multiple parameters. The findings highlight that the triangle-shaped turn exhibits enhanced turbulence generation and heat exchange efficiency compared to other shapes. Specifically, the triangle-shaped turn achieves a maximum turbulent intensity of approximately 70%, surpassing other shapes which achieve around 60%. Moreover, the triangle-shaped turn displays a longer and more substantial area of high heat exchange, resulting in an effective thermal conductivity improvement of up to 20% compared to alternative shapes. Furthermore, the analysis indicates that the triangle-shaped turn exhibits a faster increase in outlet temperature, reaching steady-state conditions within 15 seconds, while other shapes require up to 19 seconds. These results underscore the significance of turn shape in optimizing the thermal efficiency of PVT systems.
7 November 2012 in IEEJ Transactions on Electrical and Electronic Engineering
Over the years, solar has been one of the main substitutes of electricity resources worldwide including Malaysia in effort to reduce the dependency on the conventional fossil fuel. In this paper, the status of solar energy in Malaysia Plans is investigated while the techniques used in various techno-economic and economic feasibility studies on the implementation of solar energy system are analyzed. The state of awareness and understanding on solar energy among Malaysians is also determined. It has been found that a mathematical formulation method as well as an iterative technique which both consider lots of uncertainties are capable in optimally designing a photovoltaic, PV system while minimizing the cost. Meanwhile, a financial model using probabilistic and sensitivity analysis is able to provide the potential investors with the profitability of a PV project. Finally, several surveys has proven that Malaysian people are lack of awareness, information thus interest on solar technology. Therefore, in evaluating the feasibilities of a PV system, it is suggested that considerations on all solar-related variables must be taken into account while at the same time the Government of Malaysia, GoM should play the main role by providing more aggressive programmes and schemes in order to educate and expose Malaysian citizens with knowledge and skills on solar energy.