For the [0001] oriented AlGaN-based deep ultraviolet light-emitting diodes (DUV LEDs), the holes in the p-type electron blocking layer (p-EBL) are depleted due to the polarization induced positive sheet charges at the last quantum barrier (LQB)/p-EBL interface. The hole depletion effect significantly reduces the hole injection capability across the p-EBL. In this work, we propose inserting a thin AlN layer between the LQB and the p-EBL, which can generate the hole accumulation at the AlN/p-EBL interface. Meanwhile, the holes can obtain the energy when traveling from the p-EBL into the multiple quantum wells (MQWs) by intraband tunneling through the thin AlN layer. As a result, the hole injection and the external quantum efficiency (EQE) have been remarkably enhanced. Moreover, we point out that the thick AlN insertion layer can further generate the hole accumulation in the p-EBL and increase the hole energy which helps to increase the hole injection. We also prove that the intraband tunneling for holes across the thick AlN insertion layer is facilitated by using the optimized structure.
The influence of quantum-well (QW) width on electroluminescence properties of AlGaN deep ultraviolet light-emitting diodes (DUV LEDs) was studied at different temperatures. The maximum external quantum efficiency (EQE) ratios of LED with 3.5 nm QW to that with 2 nm increased from 6.8 at room temperature (RT) to 8.2 at 5 K. However, the ratios for LED with 3.5 nm QW to that with 5 nm QW decreased from 4.8 at RT to 1.6 at 5 K. The different changes of EQE ratios were attributed to the decrease of non-radiative recombination and the increase of volume of the active region. From theoretical analysis, the LED with 2-nm wells had a shallowest barrier for electron overflow due to the quantum-confined effect, whereas the LED with 5-nm wells showed the least overlap of electron and hole due to the large internal field. Therefore, the LED with 3.5 nm QW had the highest maximum EQE at the same temperature. As temperature decreased, the current for maximum EQE decreased for all the LEDs, which was believed to be due to the increase of electron which overflowed out of QWs and the decrease of hole concentration. The results were helpful for understanding the combination of polarization effect and electron overflow in DUV LEDs.
A series of AlN/GaN heterostructures were grown on 150 mm Si substrates by metal organic chemical vapor deposition (MOCVD). Different cap layer structures, including gallium nitride (GaN) and silicon nitride (SiNx), were used to passivate the heterostructure surface. A 3.5 nm thick SiNx cap is able to maintain the two dimensional electron gas (2DEG) stability in a long period. An AlN/GaN heterostructure with a 4.5 nm thick AlN barrier exhibits the best 2DEG properties, in terms of sheet resistance, carrier mobility and stability. The carrier mobility of the 2DEG can be enhanced by a combination of SiNx and GaN cap layers to over 1400 cm2/Vs.
22 June 2021 in Journal of Physics D: Applied Physics
This research investigates electrical properties of E-mode AlGaN/GaN HEMTs with n-type β-Ga2O3/p-GaN gate stack under different gate work functions of 4.6, 5.1 and 5.7 eV, respectively. The simulated results show that the device with gate work function of 5.7 eV exhibits the largest threshold voltage of 2.8 V while having the lowest saturation drain current of 0.15 A mm−1, which can be ascribed to the device having the highest Schottky barrier, leading to the least electrons collected at the AlGaN/GaN interface. Moreover, the device with gate work function of 5.7 eV shows the largest gate breakdown voltage as well as the lowest off-state gate leakage, which can be attributed to the least strength of electric field in the Ga2O3 layer. Additionally, the Fowler–Nordheim equation was used to study the mechanisms of off-state leakage.
15 October 2020 in Journal of Physics D: Applied Physics
In this work, gate-first technology was developed in an AlGaN/GaN high-electron-mobility transistor (HEMT) based on a high-quality in situ SiN x gate dielectric, targeting for high-stability power applications. The effect of the high-temperature annealing process on the Ni/SiN x gate stack was systematically investigated. Almost the same basic electrical performances were observed from gate-first and gate-last processed devices. Furthermore, the annealing-like effect on the gate-stack-located trap states was revealed in gate-first devices with obvious enhancement in threshold voltage stability, validating the high compatibility of the in situ SiN x technology with the gate-first GaN HEMT technology.