Cheng Chen

Dr. Cheng Chen

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 January 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
HLHui Li
Hui Li
CCCheng Chen
Cheng Chen
TWTongguang Wang
Tongguang Wang
LWLong Wang
Long Wang
The objective of this paper was to design configuration parameters for a stepped-lap scarf joint repair, which can be used for spar cap damage of a wind turbine blade in service and to realize the post-repair monitoring. Two experimental studies were included. First, tensile test for the unidirectional tape specimens with a large aspect ratio repaired using a multiple stepped-lap scarf joint method was carried out. The results showed that the reinforcement layer could effectively improve the load-carrying capacity of the repaired zone. The stepped-lap joint surface was identified as the weak part of the spar cap repair, which should be monitored. Second, by embedding carbon nanotube buckypaper sensors on the stepped-lap joint surface of the repaired specimens, quasi-static tensile tests and fatigue tests were carried out. According to the resistance response of the sensors, the quasi-static tensile test confirmed the failure processes, namely the stiffness turning point, damage evolution, crack propagation, and fracture. The fatigue test could accurately identify the progressive failure, namely the initial damage, damage accumulation, initial cracking, and crack propagation to structural failure. The above tests provided an important configuration parameter basis for evaluating the spar cap repair scheme and presented a promising method for the health monitoring of a spar cap after repair.

11 August 2021 in Frontiers in Energy Research
Verified
Journal Article
Open access
CCCheng Chen
Cheng Chen
TWTongguang Wang
Tongguang Wang
LWLong Wang
Long Wang
With the development of wind turbines as a result of large-scale and offshore trends, the wind turbine size is becoming increasingly larger. The passive control technique is used to alleviate the increasing loads on the blade for the sake of improving the durability of the wind turbine. The ply design of shells considering the coupling effect of bending and torsion is one of the passive control techniques. The bending torsion coupling stiffness is one of the parameters of the blade section stiffness matrix. In order to fully understand the influence of each blade stiffness parameter on the aeroelastic responses of wind turbines and to consider the influence of structural characteristics on the aeroelastic responses in blade design, the influences and sensitivity of each stiffness parameter in the 6 × 6 stiffness matrix of the blade sections on the aeroelastic responses of the wind turbines are systematically studied under steady wind condition. The aerodynamic forces in the aeroelastic model are calculated by an AeroDyn module based on blade element momentum theory, and the structural dynamic responses of the blade are calculated using generalized Timoshenko beam theory and geometric exact beam theory. The NREL baseline 5 MW wind turbine and blade properties are used in this study, where the diagonal stiffness parameters and non-diagonal stiffness parameters of the matrixes of each blade section are scaled according to certain principles. The results show that the axial stiffness, the flap-wise stiffness, and the torsional stiffness in the diagonal are sensitive to the root loads and tip displacement of the blade. The flap-wise bending torsion coupling stiffness, the flap-wise shear-torsion coupling stiffness, and the edge-wise shear-torsion coupling stiffness in the non-diagonal are also sensitive to the aeroelastic responses. For completeness, the effects of other stiffness parameters on the aeroelastic responses are also analyzed and discussed.

18 December 2019 in Sustainability
Verified
Journal Article
Open access
PDF file
LWLong Wang
Long Wang
CCCheng Chen
Cheng Chen
TWTongguang Wang
Tongguang Wang
WWWeibin Wang
Weibin Wang
A new simulation method for the aeroelastic response of wind turbines under typhoons is proposed. The mesoscale Weather Research and Forecasting (WRF) model was used to simulate a typhoon’s average wind speed field. The measured power spectrum and inverse Fourier transform method were coupled to simulate the pulsating wind speed field. Based on the modal method and beam theory, the wind turbine model was constructed, and the GH-BLADED commercial software package was used to calculate the aerodynamic load and aeroelastic response. The proposed method was applied to assess aeroelastic response characteristics of a commercial 6 MW offshore wind turbine under different wind speeds and direction variation patterns for the case study of typhoon Hagupit (2008), with a maximal wind speed of 230 km/h. The simulation results show that the typhoon’s average wind speed field and turbulence characteristics simulated by the proposed method are in good agreement with the measured values: Their difference in the main flow direction is only 1.7%. The scope of the wind turbine blade in the typhoon is significantly larger than under normal wind, while that under normal operation is higher than that under shutdown, even at low wind speeds. In addition, an abrupt change in wind direction has a significant impact on wind turbine response characteristics. Under normal operation, a sharp variation of the wind direction by 90 degrees in 6 s increases the wind turbine (WT) vibration scope by 27.9% in comparison with the case of permanent wind direction. In particular, the maximum deflection of the wind tower tip in the incoming flow direction reaches 28.4 m, which significantly exceeds the design standard safety threshold.

17 March 2023 in Frontiers in Energy Research
Verified
Journal Article
Open access
CCCheng Chen
Cheng Chen
LWLong Wang
Long Wang
MNMuhua Niu
Muhua Niu
Introduction: The blade is one of the most important parts of a wind turbine. Blade design is a complicated process involving many design links and mutual couplings. To efficiently obtain the Pareto Front and optimal blade, a novel methodology combined the improved NSGA-II with Thin-Walled Beam Theory and Classic Laminated Theory has been developed.Methods: In the optimization study, the design parameters are the thickness distribution of the spar cap and a parametric model based on blade production process is developed. The objective function is on the minimization of mass and the maximization of flap-wise stiffness. As a practical engineering application research, a 15 MW wind turbine IEA-15-240-RWT developed by NREL is used as a reference model.Results: Laws on the number of variables, blade profiles, design loads and natural frequencies present in the design have been studied through Pareto fronts obtained from multi-objective optimization results.Discussion: These laws have important implications for practical engineering design work. Meanwhile, the results show that the new methodology is effective for blade structure design, and that this approach can be easily extended to study the design of influence laws for more design parameters or more complex blade design problems.

15 April 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
CCCheng Chen
Cheng Chen
HLHui Li
Hui Li
TWTongguang Wang
Tongguang Wang
LWLong Wang
Long Wang
Wind turbines are under continuous development for large-scale deployment and oceanization, leading to the requirement of longer blades. The economic losses caused by blade replacement and shutdown have increased. The downtime caused by blade issues in a wind turbine is 8–20% of the total downtime. Many of these blade issues originate from the cracking of the blade trailing edge. The edge is more susceptible to damage due to the complex geometry, manufacturing technique, and operation conditions. The traditional design method and the expensive experimental research are not suitable for the accurate damage analysis of the trailing-edge adhesive because of simplifying assumptions and costs. This study aimed to investigate the influence of trailing-edge structural configurations on the shear fatigue life of the trailing-edge adhesive joint using finite element and stress transformation matrix (STM) methods. The structural configurations of the blade trailing edge included the position of unidirectional fiber layer (UD), chamfer of bonding line, prefabricated components, and outer over-lamination of the trailing edge. In this study, the finite element method was used to simulate the blade structure. The shell element was used for laminates, and the solid element was used for the trailing-edge adhesive joint. The basic shear fatigue properties of the adhesive were obtained by standard component tests. The shear fatigue life of the blade trailing-edge adhesive joint under given load conditions was calculated using the fatigue properties of the adhesive and STM method. The results showed that the angle of chamfering, location of UD, rigidity of the preform, and outer over-lamination all had an obvious influence on the fatigue damage of trailing-edge adhesive. The findings of this study can be used to guide blade structure design and blade production and maintenance.

19 July 2016 in Environmental Science and Pollution Research
Verified
Journal Article
Closed access
PDF file
FGFei Guo
Fei Guo
YMYunsong Mu
Yunsong Mu
CCCheng Chen
Cheng Chen
HLHaiqing Liao
Haiqing Liao
Yingchen BaiYingchen Bai
Yingchen Bai