Long-distance wireless energy transmission is realized by photoelectric conversion through lasers and photovoltaic cells. However, existing devices have low transmission power and low transmission efficiency. Exploring the main factors that limit the transmission efficiency during transmission is necessary to improve the transmission power and efficiency, and theoretically analyze these factors that affect transmission efficiency, such as beam quality, divergence angle, wavelength and so on. This will provide research directions for subsequent work. A multiwavelength laser wireless energy transmission experimental platform was built by using powersphere, laser with three different wavelengths and other devices. This platform was used for transmission efficiency verification experiment. The total electro-optical-electric conversion efficiency values obtained by the 532, 1030, and 808 nm lasers are 0.01%, 0.08%, and 0.11%, respectively. The corresponding laser-to-electric conversion efficiency values are 1.37%, 1.60%, and 0.73%, respectively. Experimental results show that the electro-optic conversion efficiency of the laser and the photoelectric conversion efficiency of the photovoltaic receiver is the main reasons for the low conversion efficiency of the system. In addition, factors such as the expansion ratio of the beam expander, laser collimation, laser uniformity at the photovoltaic receiver end, and circuit structure, affect the conversion efficiency of the system.

Laser wireless power transmission (WPT) is one of the most important technologies in the field of long-range power transfer. This technique uses a laser as a transmission medium instead of conventional physical or electrical connections to perform WPT. It has the characteristics of long transmission distance and flexible operation. The existing laser wireless power transmission system uses photovoltaic cells as a receiver, which convert light into electricity. Due to the contradiction between the Gaussian distribution of laser and the uniform illumination requirements of photovoltaic cells, the laser wireless power transmission technology has problems such as low transmission efficiency and small output power. Therefore, understanding the energy distribution changes in the laser during transmission, especially the energy change after the laser is transmitted to each key device, and analyzing the influencing factors of the energy distribution state, are of great significance in improving the transmission efficiency and reducing the energy loss in the system. This article utilizes the optical software Lighttools as a tool to establish a laser wireless power transmission model based on a powersphere. This model is used to study the energy distribution changes in the laser as it passes through various components, and to analyze the corresponding influencing factors. To further validate the simulation results, an experimental platform was constructed using a semiconductor laser, beam expander, Fresnel lens, and powersphere as components. A beam quality analyzer was used to measure and analyze the laser energy distribution of each component except for the powersphere. The output voltage and current values of various regions of the powersphere were measured using a multimeter. The energy distribution of the powersphere was reflected based on the linear relationship between photo-generated current, voltage, and light intensity. The experimental results obtained were in good agreement with the simulation results. Simulations and experiments have shown that using a beam expander can reduce divergence angle and energy loss, while employing large-aperture focusing lens can enhance energy collection and output power, providing a basis for improving the efficiency of laser wireless power transfer.

Understanding multiphase flow and gas transport occurring in electrodes is crucial for improving the performance of proton exchange membrane fuel cells. In the present study, a pore-scale model using the lattice Boltzmann method (LBM) was proposed to study the coupled processes of air–water two-phase flow and oxygen reactive transport processes in porous structures of the gas diffusion layer (GDL) and in fractures of the microscopic porous layer (MPL). Three-dimensional pore-scale numerical results show that the liquid water generation rate is gradually reduced as the oxygen consumption reaction proceeds, and the liquid water saturation in the GDL increases, thus the constant velocity inlet or pressure inlet condition cannot be maintained while the results showed that at t = 1,200,000 iterations after 2900 h running time, the local saturation at the GDL/MPL was about 0.7, and the maximum value was about 0.83, while the total saturation was 0.35. The current density reduced from 2.39 to 0.46 A cm⁻². Effects of fracture number were also investigated, and the results showed that for the fracture numbers of 8, 12, 16, and 24, the breakthrough point number was 4, 3, 3, and 2, respectively. As the fracture number increased, the number of the water breakthrough points at the GDL/GC interface decreased, the liquid water saturation inside the GDL increased, the GDL/MPL interface was more seriously covered, and the current density decreased. The pore-scale model for the coupled multiphase reactive transport processes is helpful for understanding the mechanisms inside the porous electrodes of PEMFC.

Circular airy vortex beams (CAVBs) have attracted much attention due to their “abruptly autofocusing” effect, phase singularity, and their potential applications in optical micromanipulation, communication, etc. In this paper, we numerically investigated the propagation properties of circular airy beams (CABs) imposed with different optical vortices (OVs) along the optical axis of a uniaxial crystal for the first time. Like other common beams, a left-hand circular polarized (LHCP) CAVB, propagating along the optical axis in a uniaxial crystal, can excite a right-hand circular polarized (RHCP) component superimposed with an on-axis vortex of topological charge (TC) number of 2. When the incident beam is an LHCP CAB imposed with an on-axis vortex of TC number of l = 1, both of the two components have an axisymmetric intensity distribution during propagation and form hollow beams near the focal plane because of the phase singularity. The phase pattern shows that the LHCP component carries an on-axis vortex of TC number of l = 1, while the RHCP component carries an on-axis vortex of TC number of l = 3. With a larger TC number (l = 3), the RHCP component has a larger hollow region in the focal plane compared to the LHCP component. We also studied cases of CABs imposed with one and two off-axis OVs. The off-axis OV makes the CAVB’s profile remain asymmetric throughout the propagation. As the propagation distance increases, the off-axis OVs move near the center of the beam and overlap, resulting in a special intensity and phase distribution near the focal plane.

A photovoltaic panels is a device used for converting solar and other energy into electrical energy. In laser wireless power transmission, there is a problem that the conversion efficiency of the photovoltaic panel is not as high as that of a single photovoltaic cell, and the output power is not as large as expected. This is not conducive to the popularization and use of wireless power transmission via laser. It is important to find out why the output power of the photovoltaic panel irradiated by lasers is not high. According to the laser intensity distribution equation, it is deduced that the laser in a very small area has an equivalent uniformity intensity distribution through the comparative calculation of the light intensity of two adjacent points. Then, the input non-uniform laser can be broken down into many equivalent uniform small lasers with different light intensity values. Based on this theory, the photovoltaic array model under laser was established, and it was simulated by MATLAB/Simulink. The simulation results reveal that the greater the difference between the light intensity values of these small spots, that is to say, the more non-uniform the laser, the lower the output power of the photovoltaic module illuminated by it. A multi-wavelength experimental platform was built, and comparative experiments of laser wireless power transmission were carried out using three kinds of lasers: 808, 532, and 1030 nm. The experimental result was in good agreement with the simulation result. The above results show that the deduced theory and the model based on it are correct.

The powersphere is a device used for maximizing the conversion of light in wireless energy transmission via laser. It is a spherical structure made up of thousands of photovoltaic cells. Due to the large dimensions and existence of many holes in the spherical surface, there are some drawbacks in machining, such as limited movement space of the machines, long cycle, low precision, and high cost. In this context, with a powersphere irradiated by the laser as the model, the principle of powersphere is deduced theoretically. It is proven that the illuminance value at any position on the inner wall of the powersphere is equal, and the calculation formula of this value is derived. Based on this theory and the comparative analysis of processing methods and the results of processing experiments, the structure of the powersphere is designed. The experimental processing of the powersphere is carried out by selecting the welding method. Finally, two hemispherical powersphere frames are processed, which are connected by screws to form a ball frame for the installation of photovoltaic cells. The results show that the improved design and fabricating method can process the powersphere quickly, accurately, and economically. A comparative experiment of powersphere and photovoltaic panel was carried out. The experimental results show that the powersphere has the function of light uniformity and repeated use of laser. So, the designed and processed powersphere is consistent with the theoretical analysis.