Laser wireless power transmission (WPT) is one of the most important technologies in the field of long-range power transfer. This technique uses a laser as a transmission medium instead of conventional physical or electrical connections to perform WPT. It has the characteristics of long transmission distance and flexible operation. The existing laser wireless power transmission system uses photovoltaic cells as a receiver, which convert light into electricity. Due to the contradiction between the Gaussian distribution of laser and the uniform illumination requirements of photovoltaic cells, the laser wireless power transmission technology has problems such as low transmission efficiency and small output power. Therefore, understanding the energy distribution changes in the laser during transmission, especially the energy change after the laser is transmitted to each key device, and analyzing the influencing factors of the energy distribution state, are of great significance in improving the transmission efficiency and reducing the energy loss in the system. This article utilizes the optical software Lighttools as a tool to establish a laser wireless power transmission model based on a powersphere. This model is used to study the energy distribution changes in the laser as it passes through various components, and to analyze the corresponding influencing factors. To further validate the simulation results, an experimental platform was constructed using a semiconductor laser, beam expander, Fresnel lens, and powersphere as components. A beam quality analyzer was used to measure and analyze the laser energy distribution of each component except for the powersphere. The output voltage and current values of various regions of the powersphere were measured using a multimeter. The energy distribution of the powersphere was reflected based on the linear relationship between photo-generated current, voltage, and light intensity. The experimental results obtained were in good agreement with the simulation results. Simulations and experiments have shown that using a beam expander can reduce divergence angle and energy loss, while employing large-aperture focusing lens can enhance energy collection and output power, providing a basis for improving the efficiency of laser wireless power transfer.

Spin is an intrinsic property of the photon. A method for using an externally applied dc electric field to manipulate the transfer of spin angular momentum of light in an optically active medium is presented. To discuss this, we first develop a wave coupling theory of the mutual action of natural optical activity and the linear electro-optic effect. Besides being used for analyzing the electrically controlled transfer of spin angular momentum of light, the theory can also be used to describe the propagation of light traveling along an arbitrary direction in any optically active medium with an external dc electric field along an arbitrary direction.

Circular airy vortex beams (CAVBs) have attracted much attention due to their “abruptly autofocusing” effect, phase singularity, and their potential applications in optical micromanipulation, communication, etc. In this paper, we numerically investigated the propagation properties of circular airy beams (CABs) imposed with different optical vortices (OVs) along the optical axis of a uniaxial crystal for the first time. Like other common beams, a left-hand circular polarized (LHCP) CAVB, propagating along the optical axis in a uniaxial crystal, can excite a right-hand circular polarized (RHCP) component superimposed with an on-axis vortex of topological charge (TC) number of 2. When the incident beam is an LHCP CAB imposed with an on-axis vortex of TC number of l = 1, both of the two components have an axisymmetric intensity distribution during propagation and form hollow beams near the focal plane because of the phase singularity. The phase pattern shows that the LHCP component carries an on-axis vortex of TC number of l = 1, while the RHCP component carries an on-axis vortex of TC number of l = 3. With a larger TC number (l = 3), the RHCP component has a larger hollow region in the focal plane compared to the LHCP component. We also studied cases of CABs imposed with one and two off-axis OVs. The off-axis OV makes the CAVB’s profile remain asymmetric throughout the propagation. As the propagation distance increases, the off-axis OVs move near the center of the beam and overlap, resulting in a special intensity and phase distribution near the focal plane.

A photovoltaic panels is a device used for converting solar and other energy into electrical energy. In laser wireless power transmission, there is a problem that the conversion efficiency of the photovoltaic panel is not as high as that of a single photovoltaic cell, and the output power is not as large as expected. This is not conducive to the popularization and use of wireless power transmission via laser. It is important to find out why the output power of the photovoltaic panel irradiated by lasers is not high. According to the laser intensity distribution equation, it is deduced that the laser in a very small area has an equivalent uniformity intensity distribution through the comparative calculation of the light intensity of two adjacent points. Then, the input non-uniform laser can be broken down into many equivalent uniform small lasers with different light intensity values. Based on this theory, the photovoltaic array model under laser was established, and it was simulated by MATLAB/Simulink. The simulation results reveal that the greater the difference between the light intensity values of these small spots, that is to say, the more non-uniform the laser, the lower the output power of the photovoltaic module illuminated by it. A multi-wavelength experimental platform was built, and comparative experiments of laser wireless power transmission were carried out using three kinds of lasers: 808, 532, and 1030 nm. The experimental result was in good agreement with the simulation result. The above results show that the deduced theory and the model based on it are correct.

The powersphere is a device used for maximizing the conversion of light in wireless energy transmission via laser. It is a spherical structure made up of thousands of photovoltaic cells. Due to the large dimensions and existence of many holes in the spherical surface, there are some drawbacks in machining, such as limited movement space of the machines, long cycle, low precision, and high cost. In this context, with a powersphere irradiated by the laser as the model, the principle of powersphere is deduced theoretically. It is proven that the illuminance value at any position on the inner wall of the powersphere is equal, and the calculation formula of this value is derived. Based on this theory and the comparative analysis of processing methods and the results of processing experiments, the structure of the powersphere is designed. The experimental processing of the powersphere is carried out by selecting the welding method. Finally, two hemispherical powersphere frames are processed, which are connected by screws to form a ball frame for the installation of photovoltaic cells. The results show that the improved design and fabricating method can process the powersphere quickly, accurately, and economically. A comparative experiment of powersphere and photovoltaic panel was carried out. The experimental results show that the powersphere has the function of light uniformity and repeated use of laser. So, the designed and processed powersphere is consistent with the theoretical analysis.

The powersphere is a spherical enclosed receiver composed of multiple photovoltaic cells. It serves as a replacement for traditional photovoltaic panels in laser wireless power transmission systems for optoelectronic conversion. The ideal powersphere aims to achieve a uniform distribution of light within the cavity through infinite reflections, reducing energy losses in the circuit. However, due to the high absorption rate of the photovoltaic cells, the direct irradiation area on the inner surface of the powersphere exhibits a significantly higher light intensity than the reflected area, resulting in a suboptimal level of light uniformity and certain circuit losses. To address the aforementioned issues, a method of intra-cavity beam splitting in the powersphere is proposed. This solution aims to increase the area of direct illumination and reduce the intensity difference between direct and reflected lights, thereby improving the light uniformity on the inner surface of the powersphere. Utilizing the transformation matrix of Gaussian beams, the q parameters for each optical path with beam splitting were calculated, and the equality of corresponding q values was demonstrated. Further, based on the q parameter expression for the electric field of Gaussian beams, the intensities for each optical path were calculated, and it was demonstrated that their values are equal. Additionally, an optical software was utilized to establish a model for intra-cavity beam splitting in the powersphere. Based on this model, a beam-splitting system was designed using a semi-transparent and semi-reflective lens as the core component. The light uniformity performance of the proposed system was analyzed through simulations. To further validate the effectiveness of the calculations, design, and simulations, multiple lenses were employed to construct the beam-splitting system. An experimental platform was set up, consisting of a semiconductor laser, monocrystalline silicon photovoltaic cells, beam expander, Fresnel lens, beam-splitting system, and powersphere. An experimental verification was conducted, and the results aligned with the theoretical calculations and simulated outcomes. The above theory, simulations, and experiments demonstrate that the intra-cavity beam-splitting method effectively enhances the optical uniformity within the powersphere.