The surface modification of cellulose nanocrystals (CNC) is a key intermediate step in the development of new functionalities and the tailoring of nanomaterial properties for specific applications. In the area of polymeric nanocomposites, apart from good interfacial adhesion, the high thermal stability of cellulose nanomaterial is vitally required for the stable processing and improvement of material properties. In this respect, the heterogeneous esterification of CNC with succinic anhydride was investigated in this work in order to obtain CNC with optimised surface and thermal properties. The influence of reaction parameters, such as time, temperature, and molar ratio of reagents, on the structure, morphology and thermal properties, were systematically studied over a wide range of values by DLS, FTIR, XPS, WAXD, SEM and TGA methods. It was found that the degree of surface substitution of CNC increased with the molar ratio of succinic anhydride to cellulose hydroxyl groups (SA:OH), as well as the reaction time, whilst the temperature of reaction showed a moderate effect on the degree of esterification in the range of 70–110 °C. The studies on the thermal stability of modified nanoparticles indicated that there is a critical extent of surface esterification below which only a slight decrease of the initial temperature of degradation was observed in pyrolytic and oxidative atmospheres. A significant reduction of CNC thermal stability was observed only for the longest reaction time (240 min) and the highest molar ratio of SA:OH. This illustrates the possibility of manufacturing thermally stable, succinylated, CNC by controlling the reaction conditions and the degree of esterification.

The electrically conductive, transparent, and flexible self-standing thin nanocomposite films based on copolyamide matrix (coPA:Vestamelt X1010) modified with 2D Ti₃C₂T_x (MXene) nanosheets were prepared by casting and their electrical, mechanical and optical properties and then, were investigated. The percolation threshold of the MXene filler within the coPA matrix was found to be 0.05 vol. %, and the highest determined electrical conductivity was 1.4 × 10⁻² S·cm⁻¹ for the composite filled with 5 wt. % (1.8 vol. %) of MXene. The electrical conductivity of the as-prepared MXene was 9.1 S·cm⁻¹, and the electrical conductivity of the MAX phase (the precursor for MXene preparation) was 172 S·cm⁻¹. The transparency of the prepared composite films exceeded 75%, even for samples containing 5 wt. % of MXene, as confirmed by UV spectroscopy. The dynamic mechanical analysis confirmed the improved mechanical properties, such as the storage modulus, which improved with the increasing MXene content. Moreover, all the composite films were very flexible and did not break under repeated twisting. The combination of the relatively high electrical conductivity of the composites filled with low filler content, an appropriate transparency, and good mechanical properties make these materials promising for applications in flexible electronics.

We report on the growth of monoclinic β- and orthorhombic κ-phase Ga2O3 thin films using liquid-injection metal-organic chemical vapor deposition on highly thermally conductive 4H-SiC substrates using gallium (III) acetylacetonate or tris(2,2,6,6-tetramethyl-3,5-heptanedionato) gallium (III). Both gallium precursors produced the β phase, while only the use of the latter led to growth of κ-Ga2O3. Regardless of the used precursor, best results for β-Ga2O3 were achieved at a growth temperature of 700 °C and O2 flows in the range of 600–800 SCCM. A relatively narrow growth window was found for κ-Ga2O3, and best results were achieved for growth temperatures of 600 °C and the O2 flow of 800 SCCM. While phase-pure β-Ga2O3 was prepared, κ-Ga2O3 showed various degrees of parasitic β phase inclusions. X-ray diffraction and transmission electron microscopy confirmed a highly textured structure of β- and κ-Ga2O3 layers resulting from the presence of multiple in-plane domain orientations. Thermal conductivities of 53 nm-thick β-Ga2O3 (2.13 + 0.29/−0.51 W/m K) and 45 nm-thick κ-Ga2O3 (1.23 + 0.22/−0.26 W/m K) were determined by transient thermoreflectance and implications for device applications were assessed. Presented results suggest great potential of heterointegration of Ga2O3 and SiC for improved thermal management and reliability of future Ga2O3-based high power devices.

Carbon nanotubes (CNT) provide an outstanding property spectrum which can be used to improve a wide range of materials. However, the transfer of properties from the nanoscale to a macroscopic material is a limiting factor. Different approaches of functionalizing the surface of a CNT can improve the interaction with the surrounding matrix but is connected to difficult and expensive treatments, which are usually inconvenient for industrial applications. Here, a simple and eco-friendly method is presented for the oxidation of CNT, where hydrogen peroxide (H₂O₂) is the only chemical needed and no toxic emissions are released. Also, the extensive step of the incorporation of CNT to an epoxy matrix is simplified to an ultrasonic dispersion in the liquid hardener component. The effectiveness is proven by mechanical tests of produced CNT/CFRP and compared to a conventional processing route. The combination of those simple and cost efficient strategies can be utilized to produce multiscale composites with improved mechanical performance in an ecological and economical way.