Antenna array is one of the most useable technologies in present day communication system. There are many applications like biomedical imaging, military communication and radar system where low side lobe level is an essential feature of array processor. There is a trade-off between side lobe level (SLL) and the directivity of the array. Designing an antenna array system with optimum trade-off between SLL and directivity has become a crucial problem. To suppress high SLL of output beam pattern and signal direction mismatches, some notable optimization techniques have been developed. Amplitude weighting of array elements is a well known approach for SLL control. In real-time implementation of antenna array system, the main beam may not be in the assumed direction and the actual signal is treated as an interference signal which is undesirable. Hence the robustness of an array processor against uncertainties is an important issue. In this paper, a method is proposed to keep the SLL at the desired value as well as makes the array system more applicable for real time implementation considering array uncertainties and imperfections.
5 April 2021 in IEEE Transactions on Antennas and Propagation
In this article, millimeter-wave (mmWave) wireless channel characteristics (Doppler spread and path loss modeling) for unmanned aerial vehicle (UAV)-assisted communication is analyzed and studied by emulating the real UAV motion using a robotic arm. The motion considers the actual turbulence caused by the wind gusts to the UAV in the atmosphere, which is statistically modeled by the widely used Dryden wind model. The frequency under consideration is 28 GHz in an anechoic chamber setting. A total of 11 distance points from 3.5 to 23.5 ft in increments of 2 ft were considered in this experiment. At each distance point, three samples of data were collected for better inference purposes. In this emulated environment, it was found out that the average Doppler spread at these different distances was around −20 and +20 Hz at the noise floor of −60 dB. On the other hand, the path loss exponent was found to be 1.843. This study presents and lays out a novel framework of emulating UAV motion for mmWave communication systems, which will pave the way out for future design and implementation of next-generation UAV-assisted wireless communication systems.
29 July 2020 in IEEE Microwave and Wireless Components Letters
This letter presents the application of the fT-doubler technique, for the first time, to improve the unity-gain frequency (fT) of inverse-mode (IM) silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs). An fT-doubler structure, which used three identical SiGe HBTs with the same emitter area of 0.07 (width) x 0.9 (length) μm², is implemented in a commercial 0.13-μm SiGe-BiCMOS technology platform. A peak fT of 77 GHz is extrapolated for the IM fT doubler, whereas a peak fT of a single IM SiGe HBT is found to be 53 GHz, exhibiting an increase of about 46% in fT from the fT-doubler technique. The maximum oscillation frequency of the IM fT doubler using Mason's unilateral gain is about 158 GHz. In addition, small-signal model parameters of the IM fT doubler are presented, which show the IM fT-doubler structures can be treated as a single transistor element for high-frequency circuit design.
It has been known that negative feedback loops (internal and external) in a SiGe heterojunction bipolar transistors (HBT) DC current mirrors improve single-event transient (SET) response; both the peak transient current and the settling time significantly decrease. In the present work, we demonstrate how radiation hardening by design (RHBD) techniques utilized in DC bias blocks only (current mirrors) can also improve the SET response in AC signal paths of switching circuits (e.g., current-mode logic, CML) without any additional hardening in those AC signal paths. Four CML circuits both with and without RHBD current mirrors were fabricated in 130 nm SiGe HBT technology. Two existing RHBD techniques were employed separately in the current mirrors of the CML circuits: (1) applying internal negative feedback and (2) adding a large capacitor in a sensitive node. In addition, these methods are also combined to analyze the overall SET performance. The single-event transients of the fabricated circuits were captured under the two-photon-absorption laser-induced single-event environment. The measurement data clearly show significant improvements in SET response in the AC signal paths of the CML circuits by using the two radiation hardening techniques applied only in DC current mirrors. The peak output transient current is notably reduced, and the settling time upon a laser strike is shortened significantly.
For performance-driven systems such as space-based applications, it is important to maximize the gain of radio-frequency amplifiers (RFAs) with a certain tolerance against radiation, temperature effects, and small form factor. In this work, we present a K-band, compact high-gain RFA using an fT-doubler topology in a silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) technology platform. The through-silicon vias (TSVs), typically used for small-size chip packaging purposes, have been effectively utilized as an adjustable matching element for input impedance, reducing the overall area of the chip. The proposed RFA, fabricated in a modest 0.35 µm SiGe technology, achieves a gain of 14.1 dB at 20 GHz center frequency, and a noise figure (NF) of 11.2 dB at the same frequency, with a power consumption of 3.3 mW. The proposed design methodology can be used for achieving high gain, avoiding a complex multi-stage amplifier design approach.