The current state of the rheology of various polymeric and other materials containing a high concentration of spherical solid filler is considered. The physics of the critical points on the concentration scale are discussed in detail. These points determine the features of the rheological behavior of the highly filled materials corresponding to transitions from a liquid to a yielding medium, elastic–plastic state, and finally to an elastic solid-like state of suspensions. Theoretical and experimental data are summarized, showing the limits of the most dense packing of solid particles, which is of key importance for applications and obtaining high-quality products. The results of model and fine structural studies of physical phenomena that occur when approaching the point of filling the volume, including the occurrence of instabilities, are considered. The occurrence of heterogeneity in the form of individual clusters is also described. These heterogeneous objects begin to move as a whole that leads to the appearance of discontinuities in the suspension volume or wall slip. Understanding these phenomena is a key for particle technology and multiphase processing.
Three-dimensional printing is one of the most promising areas of additive manufacturing with a constantly growing range of applications. One of the current tasks is the development of new functional materials that would allow the manufacture of objects with defined magnetic, electrical, and other properties. In this work, composite magnetic filaments for 3D printing with tunable magnetic properties were produced from polylactic acid thermoplastic polymer with the addition of magnetic ferrite particles of different size and chemical composition. The used magnetic particles were cobalt ferrite CoFe2O4 nanoparticles, a mixture of CoFe2O4 and zinc-substituted cobalt ferrite Zn0.3Co0.7Fe2O4 nanoparticles (~20 nm), and barium hexaferrite BaFe12O19 microparticles (<40 µm). The maximum coercivity field HC = 1.6 ± 0.1 kOe was found for the filament sample with the inclusion of 5 wt.% barium hexaferrite microparticles, and the minimum HC was for a filament with a mixture of cobalt and zinc–cobalt spinel ferrites. Capabilities of the FDM 3D printing method to produce parts having simple (ring) and complex geometric shapes (honeycomb structures) with the magnetic composite filament were demonstrated.
The regularities of branching and thermal destruction processes of polysulfones of different chemical structure at 150–500°С are studied depending on the nature of the reactive medium and blocking method of the terminal groups with the use of a special device for a gas chromatograph allowing one to investigate the branching and thermal destruction of polymers. It is found that the nature of the solvent and deactivator of the terminal hydroxyl groups substantially affects the crosslinking and destruction processes of polysulfones.
Polyphenylene sulfones (PPSU) blends with different viscosities have been studied. It is shown that the blends have a single-phase structure, regardless of the viscosities of the mixed polymers. It was found that blends having close values of the melt flow index (MFR) are also characterized by a similar melt viscosity in a wide range of shear rates, regardless of the viscosities of its constituent components. It has been found that PPSU blends with smaller MFR differences exhibit higher heat resistance and stability of mechanical properties, while blends with similar viscosity containing oligomers exhibit a broader molecular weight distribution (MWD) and have lower thermal and mechanical properties.
3D printing of polyolefins, such as polyethylene (PE) and polypropylene (PP), is of great practical interest due to the combination of high properties of these materials. However, the use of these materials in 3D printing is associated with many problems due to their high rate of crystallization, which causes shrinkage and warpage of the printed object. In this regard, blends of PE and ethylene-vinyl acetate copolymer (EVA) of various compositions were investigated for 3D printing. It was found that with an increase in the concentration of EVA, an increase in the pseudoplastic effect and amorphization of PE occurs. It has been shown that with an increase in the EVA content, the degree of crystallinity of PE decreases slightly (by 11% at a content of 80% EVA); however, a significant decrease in the rate of crystallization of PE is observed (by 87.5% at the same EVA concentration). It was found that PE and EVA are completely compatible in the amorphous phase and partially compatible in the crystalline phase, which leads to a slight decrease in the melting point of PE. The introduction of EVA also leads to a significant increase in impact strength: the maximum value is achieved at a 50/50 ratio, which is five times the value of the initial PE and two times the value of the initial EVA. At the same time, it was revealed that EVA leads to a gradual decrease in the elastic modulus and strength of PE, the change of which generally obeys the additivity rule. The resulting printing filaments are characterized by a certain ovality due to their shrinkage, which decreases with increasing EVA content and reaches a minimum value at a PE/EVA ratio of 30/70. This composition also demonstrates the lowest shrinkage of the printed sample and higher processability during printing.
For the first time, the effect of the solvent and monomer ratio on molecular weight, chemical structure, and mechanical, thermal, and rheological characteristics of polyphenylene sulfone has been studied. When dimethylsulfoxide (DMSO) is used as a solvent, cross-linking occurs during the processing of the polymer, which is accompanied by an increase in melt viscosity. This fact sets a pressing need for the complete removal of DMSO from the polymer. The best solvent used for the production of PPSU is N,N-dimethylacetamide. This study of the molecular weight characteristics of polymers by gel permeation chromatography showed the stability of the polymers practically does not change with a decrease in molecular weight. The synthesized polymers correspond in tensile modulus to the commercial analog Ultrason-P, while exceeding it in terms of tensile strength and relative elongation at break. Thus, the developed polymers are promising for spinning hollow fiber membranes with a thin selective layer.