In this communication, artificial neural networks are used to estimate the initial structure of a multiband planar antenna. The neural networks are trained on a set of selected normalized multiband antennas characterized by time-efficient modal analysis with limited accuracy. Using the Deep Learning Toolbox in Matlab, several types of neural networks have been created and trained on the sample planar multiband antennas. In the neural network learning process, suitable network types were selected for the design of these antennas. The trained networks, depending on the desired operating bands, will select the appropriate antenna geometry. This is further optimized using Newton’s method in HFSS. The use of the neural pre-design concept speeds up and simplifies the design of multiband planar antennas. The findings presented in this paper will be used to refine and accelerate the design of planar multiband antennas.
In this paper, a new method for detecting and estimating the parameters of a binary phase shift keying (BPSK) signal, based on a cross-correlation function, is proposed. The proposed method consists of two stages. The first stage is used to detect or estimate a signal carrier frequency, and the second stage is used to estimate its pulse width or symbol rate. Firstly, the proposed method is investigated by use of a simulated BPSK signal in the form of Barker Codes 7, 11, and 13 in the MATLAB environment. Based on the simulation results, the functionality of this method is verified using a real-time BPSK signal generated by an E8267C generator. This is described in the second part of this paper. The experimental test results confirm that the proposed method is able to detect and estimate the parameters of all BPSK signals with
Monitoring the Earth’s surface from the low Earth orbit (LEO) by synthetic aperture radar (SAR) provides meaningful information about a number of human activities such as the ecosystem, agriculture, and of course security matters. During its operation in LEO orbits, spaceborne SAR, at altitudes between 200 km and 2000 km, inherently emit electromagnetic signals toward the Earth’s surface. It has been experimentally verified that it is possible to detect and intercept spaceborne SAR signals at a distance of hundreds of kilometers by a single electronic support measure (ESM) non-comms sensor, placed on the Earth’s surface. The work described in this document is a follow-up to the paper and describes the principle of a new non-cooperative passive tracking method of spaceborne SAR carriers, tracked by four ground-based passive ESM non-comms sensors. These sensors used the time difference of arrival (TDOA) method in order to determine the current spaceborne SAR position in LEO orbits. Simulations were performed to assess the impact of ESM sensor configurations on the SAR’s signal interception and positioning error. The simulation results showed that the proposed method is sufficient to detect a spaceborne SAR position in LEO.
The main aim of this review is to describe in detail an advanced technique to detect and estimate the prior unknown parameters of intra-pulse modulated signals and the verification with typical radar signals. The method is approved for detecting parameters successfully, including chirp rate, carrier frequency, and pulse width. The review presents already-done research on detecting and estimating single and multi-component linear frequency modulation (LFM) and binary phase shift keying (BPSK) signals in a strong noise environment and studies the technique on one more case, a mixture of LFM and BPSK signals. Firstly, the accuracy of the revised technique is shown in detecting and estimating parameters of a single and multi-component LFM signal in white noise and a mixture of continuous wave signals and noise, or a single BPSK signal in strong white noise. All of them have been done in the existing studies. This method is continuously tested in the second part by detecting a mixture of LFM and BPSK signals and estimating their parameters in intense noise. The tested experimental results demonstrate that the technique can detect single and multi-component real-time LFM signals, single BPSK as well as verification with a mixture of real-time LFM and BPSK signals with $$SNR \ge - 12{\text{ dB}}$$ is performed. As a result, the technique outperforms the existing detection methods based on machine learning and artificial intelligence.
In this paper, we propose a new approach to passively locate the 3D position of a signal source. This novel technique, called the power gain difference (PGD), is based only on measuring the received signal strength (RSS) with multiple sensors deployed in the area of interest, while the target transmit power or the equivalent isotropic radiated power (EIRP) is assumed to be unknown. Next, the signal source position is estimated using the knowledge of the ratios of RSS measured on different sensors. First, this article presents the geometric representation and the analytical solution of the model of the PGD technique. Second, the PGD dilution of precision was analyzed in order to gauge the accuracy of measuring the RSS. Finally, a numerical simulation of the performance of the proposed method was carried out and the results are discussed. It seems that the PGD technique has the potential to be a simple and effective solution of the 3D localization problem.
In this article, a new technique for determination of 2D signal source (target) position is proposed. This novel approach, called the Inscribed Angle (InA), is based on measuring the time difference of sequential irradiation by the main beam of the target antenna’s radiation pattern, using Electronic Support Measures (ESM) receivers, assuming that the target antenna is rotating and that its angular velocity is constant. In addition, it is also assumed that the localization system operates in a LOS (Line of Sight) situation and that three time-synchronized sensors are placed arbitrarily across the area. The main contribution of the article is a complete description of the proposed localization method. That is, this paper demonstrates a geometric representation and an InA localization technique model. Analysis of the method’s accuracy is also demonstrated. The time of irradiation of the receiving station corresponds to the direction in which the maximum received signal strength (RSS) was measured. In order to achieve a certain degree of accuracy of the proposed positioning technique, a method was derived to increase the accuracy of the irradiation time estimation. Finally, extensive simulation was conducted to demonstrate the performance and accuracy of our positioning method.