Pedro Mendonça Dos Santos

Prof. Pedro Mendonça Dos Santos

Academia Militar, Instituto Universitário Militar; Instituto de Telecomunicações, Portugal
orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 February 2023 in Energies
Verified
Journal Article
Open access
PDF file
JTJoão Paulo N. Torres
João Paulo N. Torres
Ricardo A. Marques LameirinhasRicardo A. Marques Lameirinhas
Ricardo A. Marques Lameirinhas
CBCatarina P. Correia V. Bernardo
Catarina P. Correia V. Bernardo
HVHelena Isabel Mota Veiga
Helena Isabel Mota Veiga
Pedro Mendonça Dos SantosPedro Mendonça Dos Santos
Pedro Mendonça Dos Santos
Solar cell equivalent circuit modelling is usually based on continuous I-V models, with a set of data obtained by analytical expressions. This work proposes an almost discrete novel mathematical method and correspondent electrical model, based on the I-V curve adjustment at every two adjacent points. It is based on the discretisation of any diode model behaviour, such as the 1M5P (also known as 1D5P) or the 1M7P (also known as 2D7P). For this reason, the model is named d1MxP, meaning that it is a discrete (d) model (1M) with x parameters (xP). The modelling methodology validation process uses experimental data already published in the literature. According to the presented results, the proposed method shows increased accuracy when compared to the 1M5P or 1M7P equivalent models. The accuracy on the maximum power point and fill factor determination is relevant, resulting in an improvement of up to 3.34% in the maximum power, up to 5.70% in its voltage and up to 8.20% in its current, for the analysed data. Furthermore, Fill Factor values, have variation from up to 35.98%. The temperature influence on the silicon solar cell is also analysed, to validate the results. The proposed method allows highly accurate curve fitting to the (experimental) points and consequently, to obtain a more accurate model to analyse the performance of solar cells under different conditions.

15 April 2019 in Sensors
Verified
Journal Article
Open access
PDF file
DBDuarte Batista
Duarte Batista
LOLuis Bica Oliveira
Luis Bica Oliveira
NPNuno Paulino
Nuno Paulino
CCCarlos Carvalho
Carlos Carvalho
JPJoao Pedro
Joao Pedro
Pedro Mendonça Dos SantosPedro Mendonça Dos Santos
Pedro Mendonça Dos Santos
This paper describes an energy harvesting system composed of an organic photovoltaic cell (OPV) connected to a DC–DC converter, designed in a 130 nm Complementary Metal-Oxide-Semiconductor (CMOS) technology, with a quasi- maximum power point tracking (MPPT) algorithm to maximize the system efficiency, for indoor applications. OPVs are an emerging technology with potential for low cost indoor light energy harvesting. The OPV current-voltage curves (I-V) under an irradiance of solar simulator Oriel Sol 3A, at room temperature, are obtained and an accurate electrical model is derived. The energy harvesting system is subjected to four different indoor light sources: 35 W halogen, 3.5 W LED, 5 W LED, and 7 W LED, positioned at three different heights (0.45 m, 0.26 m, and 0.11 m), to evaluate the potential of the system for indoor applications. The measurements showed maximum efficiencies of 60% for 35 W halogen and 45% for 7 W LED at the highest distance (0.45 m) and between 60% (5 W LED) and 70% (35 W halogen), at the shorter distance (0.11 m). Under irradiation, the integrated CMOS circuit presented a maximum efficiency of 75.76%, which is, to the best of the authors’ knowledge, the best reported power management unit (PMU) energy system using organic photovoltaic cells.

1 August 2002 in Microelectronics Journal
Verified
Journal Article
Closed access
Pedro Mendonça Dos SantosPedro Mendonça Dos Santos
Pedro Mendonça Dos Santos
ACA.P Casimiro
A.P Casimiro
MLM Lança
M Lança
MSM.I Castro Simas
M.I Castro Simas

9 July 2007 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SFSaulo Finco
Saulo Finco
WMWellington Melo
Wellington Melo
FCFernando Castaldo
Fernando Castaldo
JPJOSE ANTENOR POMILIO
JOSE ANTENOR POMILIO
BBBeatriz Vieira Borges
Beatriz Vieira Borges
Pedro Mendonça Dos SantosPedro Mendonça Dos Santos
Pedro Mendonça Dos Santos
This paper describes a course in Smart Power based on the introduction of an innovative educational tool-a preprocessed Smart Power integrated circuit. The methodology used to introduce students to the issue of Smart Power design, resorting to low cost standard CMOS technology is presented. The theoretical support is envisaged to provide the required knowledge to specify characteristics and performance of the most common blocks used in Smart Power and to develop skills for monolithic integration. Through design, simulation, and experimental characterization, the students were able to experience the different steps of a Smart Power project, from the power device basic switching cell mask layout to the final system prototype, in 60 hours of a one semester course. The referred Smart Power Integrated Circuit (IC) embedding analog and digital basic blocks and high-voltage transistor arrays is the key idea to the presented pedagogical methodology. Based on this Smart Power IC, different topologies required by power electronics and power management systems were implemented. A complete system illustrative example-a step-down hard-switching dc-dc regulator (buck regulator)-implemented by the students is shown and discussed.

Verified
Journal Article
Open access
PDF file
Pedro Mendonça Dos SantosPedro Mendonça Dos Santos
Pedro Mendonça Dos Santos
ASAntónio Joaquim Serralheiro
António Joaquim Serralheiro
BBBeatriz Borges
Beatriz Borges
JTJoão Paulo N. Torres
João Paulo N. Torres
Ana CharasAna Charas
Ana Charas
This work studies two circuit topologies to step-up the voltage supplied by an organic photovoltaic (OPV) cell. Comparison and validation of the proposed topologies are accomplished throughout analytical, simulation, and experimental results. Two circuit solutions were found more suitable to boost the harvested OPV cell low voltage, depending on the load condition: the classical hard-switching boost converter and a multilevel boost converter. Both experimental circuits include the drive of the MOSFET switch based on an LC oscillator at 1.2 MHz, allowing the implementation of a conversion system, supplied by voltages as low as 500 mV, with output voltages from 1.2 V up to 7 V, under solar simulator conditions. The circuit area for each converter prototype is 2.35 cm2, with a total area below 3.0 cm2 for the overall energy harvesting system, including the OPV cell, which makes this proposal an extremely compact solution for ultra-low power harvesting applications.

31 January 2007 in Microelectronics Journal
Verified
Journal Article
Closed access
Pedro Mendonça Dos SantosPedro Mendonça Dos Santos
Pedro Mendonça Dos Santos
VCVitor Costa
Vitor Costa
MGM.C. Gomes
M.C. Gomes
BBBeatriz Borges
Beatriz Borges
MLMário Lança
Mário Lança