Yannan Shi

Dr. Yannan Shi


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 November 2018 in IEEE Access
Verified
Journal Article
Open access
YLYang Liu
Yang Liu
YSYannan Shi
Yannan Shi
JGJinxi Guo
Jinxi Guo
YWYiying Wang
Yiying Wang
In this paper, an efficient technique in fault detection and localization of leaky coaxial cable (LCX) is presented. The approach utilizes a high-resolution reflectometry technique, which injects a reference signal into an LCX and handles the reflected signal to locate the fault. The reference signal adopts a linear frequency modulation (LFM) signal by an approximately rectangular magnitude spectrum, which can ensure that the detection distance is large enough. And the pulse compression technique is used to improve the resolution of the reflected signal. Therefore, the approach can solve the contradiction between the detection distance and the high-resolution. The proposed method is verified by detecting various types of faults at different distances in MSLYFYVZ-50-9 LCX.

14 June 2021 in IEEE Access
Verified
Journal Article
Open access
YSYannan Shi
Yannan Shi
PQPenglei Qi
Penglei Qi
YLYang Liu
Yang Liu
JGJinxi Guo
Jinxi Guo
YWYiying Wang
Yiying Wang
DWDahu Wang
Dahu Wang
As a continuous antenna, the leaky coaxial cable (LCX) is widely used in wireless communication of closed or semi-closed areas such as the subway, mine, tunnel, etc. Usually, LCX networks are required in coal mines. Its channel characteristics are of great significance to mobile communication and mine safety. This paper presents an effective channel modeling and optimization method that combines the state transition and the particle swarm optimization (PSO) algorithms for the LCX network. First, a channel model can be established with a few parameters based on the state transition method, which can describe the complex transfer function of the LCX network; then, taking the transfer characteristics of the LCX network as the optimization objective, which should be consistent with the measured results. And the established objective function is optimized and designed with the PSO algorithm. Finally, the proposed method is validated by comparing the measured results and the model-based simulations on two test LCX networks. The experimental results show that the absolute error between the proposed model and the measurement model is less than that of other models at any frequency point. The proposed model can accurately obtain all responses between point-to-point channels at one time. It will help to accurately obtain the performance of different LCX networks and help to detect and locate faults in future studies.

13 May 2022 in The Journal of Supercomputing
Verified
Journal Article
Closed access
PDF file
CZChongchong Zhang
Chongchong Zhang
YSYannan Shi
Yannan Shi
JLJiangong Liu
Jiangong Liu
SJShuaishuai Jiang
Shuaishuai Jiang
HWHanqiu Wang
Hanqiu Wang
YWYiying Wang
Yiying Wang

18 December 2023 in Frontiers in Materials
Verified
Journal Article
Open access
HWHanqiu Wang
Hanqiu Wang
YSYannan Shi
Yannan Shi
JZJiawei Zhao
Jiawei Zhao
YWYiying Wang
Yiying Wang
CLChengyong Liu
Chengyong Liu
YWYuyi Wu
Yuyi Wu
In order to facilitate ventilation or transportation, many coal mines usually excavate an empty roadway in the middle of the mining working face. Under the influence of mining pressure, empty roadways are easily damaged, seriously threatening coal mines’ safety. Because the traditional support method of the empty roadway has the problems of low efficiency, high cost, and low strength, this paper researches the coal-based concrete support material with better effect. The grading test of coal aggregate was carried out, and it was found that the percentage of small-size aggregate greatly influenced the reduction of aggregate porosity in the stacked state. To solve the problems of the high cost of strengthening support methods such as high water material support in empty roadways, which could be more conducive to recovery and reduce coal quality. The research on empty roadways supports concrete material with coal as aggregate, making the working face recover coal resources safely and efficiently. The optimum gradation test of the total is to enhance the strength of support and solve the problem of low power and difficult cementation of coal. Based on the hydration analysis of cementitious material, the coal-based concrete, mainly composed of low-cost slag, is determined. The cementitious material with simple composition, rapid setting, and fast hardening was found. It is proved that the mechanical properties and molding effect of coal-based concrete support composed of gypsum, GGBFS, and clinkercement are better than those of commercial cement. The structural model of “surrounding rock-empty roadways-coal pillar-support” is established. The calculation method and check basis of empty roadways support resistance N1 are obtained. The results of industrial application verified that coal-based concrete could effectively protect empty roadways without affecting the productivity of coal mines.

14 February 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
BLBoyu Li
Boyu Li
TDTao Ding
Tao Ding
YWYanhui Wu
Yanhui Wu
ZNZhen Nie
Zhen Nie
QWQian Wu
Qian Wu
MZMianping Zheng
Mianping Zheng
The mine roadway is a special restricted space where wireless signals cannot freely propagate. The research on the transmission characteristics of wireless signals in mine roadways is of great significance for establishing a safe and reliable underground communication system. In this context, the transmission characteristics of wireless signals with a frequency of 700 MHz in the roadway are studied using the three-dimensional (3D) ray-tracing method. The calculation of the vertical dimension of the roadway is increased, and a roadway model is established to more comprehensively reflect the transmission characteristics of the signal in the roadway. The results show that the field strength in the near-source region is high, the attenuation is fast, and the fluctuation is strong, while the waveform in the far-source region gradually stabilizes and decays. The signal strength is related to the number of reflections; the more reflections, the weaker the signal strength. When the transmitting end is close to the edge of the roadway wall, the signal attenuation is faster and the fluctuation amplitude is stronger. The signal strength in the roadway is affected by the cross-sectional size of the rectangular roadway, and the larger the length and width dimensions, the better the waveguide can be formed in the roadway. The simulation results of wireless signal transmission in the roadway are compared with the measured results from a coal mine in Ganhe, Huozhou, and the results show that the model established by the 3D ray-tracing method can predict the field strength distribution of wireless signal. This study provides a theoretical foundation and practical guidance for improving the reliability and quality of wireless signal transmission in mine tunnels. Future research directions can further optimize algorithms, enhance transmission rates, and improve interference resistance to meet the needs of wireless communication in mine tunnels.

1 July 2020 in IEEE Access
Verified
Journal Article
Open access
YLYang Liu
Yang Liu
YWYiying Wang
Yiying Wang
SYShanfei Yan
Shanfei Yan
JGJinxi Guo
Jinxi Guo
YSYannan Shi
Yannan Shi
When integrating evolutionary algorithms into the process of the design of modular robots, the "reality gap" problem leads to the difference between simulation and reality. A modular robot transplantation method based on the improved inverse distance weighting method proxy model is presented. Based on the plane moving task, the portability of the modular robot consisting of EMERGE modules of different shapes and types was experimentally studied. The information of other real robots can be predicted according to the limited evolutionary data of real robots. It is no need to do all the evaluation experiments on a physical robot. The number and complexity of experiments are reduced. the experiment efficiency is improved. This method can effectively reduce the performance difference between the results of simulation and the real robot caused by the "reality gap" problem, and the portability of modular robots improves greatly.