Wide-angle optical systems play a vital role in imaging applications and have been researched for many years. In traditional lenses, attaining a wide field of view (FOV) by using a single optical component is difficult because these lenses have crucial aberrations. In this study, we developed a wide-angle metalens with a numerical aperture of 0.25 that provided a diffraction-limited FOV of over 170° for a wavelength of 532 nm without the need for image stitching or multiple lenses. The designed wide-angle metalens is free of aberration and polarization, and its full width of half maximum is close to the diffraction limit at all angles. Moreover, the metalens which is designed through a hexagonal arrangement exhibits higher focusing efficiency at all angles than most-seen square arrangement. The focusing efficiencies are as high as 82% at a normal incident and 45% at an incident of 85°. Compared with traditional optical components, the proposed metalens exhibits higher FOV and provides a more satisfactory image quality because of aberration correction. Because of the advantages of the proposed metalens, which are difficult to achieve for a traditional single lens, it has the potential to be applied in camera systems and virtual and augmented reality.
Focus-tunable lenses are indispensable to optical systems. This paper proposes an electrically modulated varifocal metalens combined with twisted nematic liquid crystals. In our design, a metalens is employed to focus on different points depending on the polarization state of incident light. We demonstrated that the varifocal metalens has a sub-millisecond response time. Furthermore, the numerical aperture of both the first and second focal points can be customized to achieve a wide range of 0.2–0.7. Moreover, the full width at half maximum approached the diffraction limit at multiple focal points. Because of the advantages of our proposed electrically modulated metalens, it has the potential for application in optical technology and biomedical science, both of which require high image quality and a rapid response time.
Metasurface has demonstrated potential and novel optical properties in previous research. The prevailing method of designing a macroscale metasurface is based on the local periodic approximation. Such a method relies on the pre-calculated data library, including phase delay and transmittance of the nanostructure, which is rigorously calculated by the electromagnetic simulation. However, it is usually time-consuming to design a complex metasurface such as broadband achromatic metalens due the required huge data library. This paper combined different numbers of nanofins and used deep neural networks to train our data library, and the well-trained model predicted approximately ten times more data points, which show a higher transmission for designing a broadband achromatic metalens. The results showed that the focusing efficiency of designed metalens using the augmented library is up to 45%, which is higher than that using the original library over the visible spectrum. We demonstrated that the proposed method is time-effective and accurate enough to design complex electromagnetic problems.
This Letter describes the design procedure and process optimization of the electrically bifocal metalens. In our design, horizontal and vertical polarization is manipulated by applying a suitable voltage to a twisted nematic liquid crystal (TN-LC) cell. Each nanostructure is designed to be a rectangular prism, making different polarizations of light experience various phase delays, thus causing bi-focus. We selected lithographical methods to fabricate our metalens because of the minimum physical size, which can be as small as 50 nm, and the maximum aspect ratio, which is as high as 15. Furthermore, to increase the tolerance and make the sidewall vertical and smooth, we coated different characteristics of photoresist sensitivity to the upper and lower layers. After the development, the mushroom-type photoresist makes Ni easier to strip while in the lift-off process, thus increasing the quality of the whole metalens. Our experiment shows that the focal lengths and focusing efficiencies corresponding to the two polarizations are similar to the simulation results. The proposed electrically modulated bifocal metalens can be utilized in different applications and combined with other optical components.
30 October 2025 in IEEE Photonics Technology Letters
This Letter presents the design and properties of a polarization-selective metasurface tailored for smart buildings and visible light communication. The proposed design features unit cells with a perforated hexagonal structure, enabling resonance modes for specific polarizations. The results demonstrate high transmission around 28 GHz for a particular linear polarization, with a transmittance of approximately 70%, while reflecting the orthogonal polarization with a transmittance below 5%. Moreover, the metasurface is compatible with wide-angle 5G signals and achieves 85% high transmittance in the visible light spectrum, regardless of polarization. Unlike prior multilayer approaches, our structure is realized by a single patterned copper layer on a dielectric substrate, enabling scalable fabrication and practical integration. This polarization-selective metasurface can seamlessly integrate into the smart glass, providing natural light transmission while filtering communication signals for enhanced privacy and functionality.