In this article, we introduce the first European open source process design kit (PDK), namely IHP-Open130-G2. We provide a concise history of the PDK itself and offer a brief comparison with some alternative open source PDKs, such as SKY130 and GF180MCU. The article also includes a process description and details on deliverables, offering insights into available devices, models, supported open source tools, and workflows. As the IHP-Open130-G2 is currently under development, we present key points outlining future activities. This aims to inform and attract users to join the open source silicon community. The concluding section of the article compares measurement results for active devices with compact model results. The article concludes with a cryptographic Internet protocol (IP) core based on IHP-Open130-G2 as an exemplary use case.
This paper proposes a new communication protocol for output-feedback control through multi-hop Wireless Sensor Network (WSN). The protocol is based on a Hop-by-Hop transport scheme and is especially devised to simultaneously fulfill two conflicting criteria: the network energy consumption and the stability/performance (in terms of norm) of the closed-loop system. The proposed protocol can be implemented by means of three heuristics, basically using distinct rules to control the maximum number of retransmissions allowed in terms of the voltage level of the batteries of the network nodes. As another contribution, a Markov jump based representation is proposed to model the packet loss in the communication channel, giving rise to a systematic procedure to determine the transition probability matrix and the Markov chain operation modes of a network with multiple information sources. The synthesis of the output-feedback controller is made in two steps (observer filter plus a state-feedback controller) for the Markov model assuming partial availability of the operation modes. The efficiency and applicability of the communication protocol is illustrated by means of a numerical experiment, based on a physical model of a coupled tanks plant. The features of each heuristic of implementation of the proposed protocol are presented in the numerical comparisons.
Parameterization of bats’ echolocation signal is essentially based on determination of spectral power density by means of the classic Fourier transform FFT. This study presents an alternative solution in this area of research, that is parametric and non-parametric modelling of short-time signals. The above mentioned methods are based on modelling of white noise with the use of digital filters the transmission of which was set in a way that allows the output signal to be as close to the modelled signal as possible. Proper selection of parameterization method — MA (Moving Average), AR (Autoregressive), ARMA (Autoregressive Moving Average), in respect of the character of signal spectrum (line spectrum, noise) maximally reduces the number of filter coefficients and improves the accuracy of bat’s signal modelling. The work also presents the possibility of using the suggested parameterization methods in automatic species identification
In this paper, a method for estimating snow pressure reflection coefficient based on non-contact ultrasound examination is described. A constant frequency and air-coupled ultrasound pulses were used in this study, which incorporates a parametric method for reflected energy estimation. The experimental part was carried out in situ in the Antarctic, where the snow parameters were measured along with meteorological data. The proposed method represents a promising alternative for estimating the snow-water equivalent, since it uses a parametric approach, which does not require measurements of absolute values for acoustic pressure.
This paper presents a solution that utilises ultrasonic technology to allow monitoring snow layer thickness or water level based on measurement from air. It describes the principle of operation of a measurement device using three methods of compensating for changing external factors affecting appliance’s precision. Block diagram of the device is also provided. In order to verify the proposed solutions, the research team tested the device in laboratory and operating conditions. The results obtained this way make it possible to select a configuration of device operation depending on the required measurement precision and limitations associated with installing the system for actual operation.
This work proposes a methodology for the automated sizing of transistors in analog integrated circuits, based on a modular and hierarchical representation of the circuit. The methodology combines structured design techniques and systematic design flow to generate a hierarchy of simplified macromodels that define their specifications locally and are interconnected with other macromodels or transistor-level primitive blocks. These primitive blocks can be described using symbolic models or pre-characterized data from look-up tables (LUTs). The symbolic representation of the system is obtained using Modified Nodal Analysis (MNA), and the exploration of each block is performed using local design spaces constrained by top-level specifications. The methodology is validated through the design of low dropout voltage regulators (LDOs) for DC-DC integrated power systems using open-source tools and three process design kits: Sky130A, GF180MCU, and IHP-SG13G2. Results show that the methodology allows the exploration of several topologies and technologies, demonstrating its versatility and modularity, which are key aspects in analog design.