14 March 2016 in IEEE Microwave and Wireless Components Letters
In this letter, we propose an N-way unequal power division Wilkinson power divider (PD) with physical output port separation. These PDs employ isolation impedances at arbitrary positions within quarter-wave-long transmission lines, and hence both electrical isolation and physical separation can be obtained between output ports. Design equations are derived, meeting the impedance matching and isolation requirements of the PD. The fabricated 2-way (1:2) and 3-way (1:2:1) PDs operating at 2.0 GHz exhibit excellent insertion loss, return loss, and isolation performance with the output ports physically separated.
29 November 2024 in IEEE Access
This paper presents the design and implementation of a high-power amplifier (HPA) using a 250-nm gallium nitride (GaN) high electron mobility transistor (HEMT) process on a silicon carbide substrate. The HPA is engineered to optimize both output power and power density relative to chip size. The 1st and 2nd drive stages utilize individual source via transistors (ISV TRs) for high gain and efficiency, while the output stage employs outside source via transistors (OSV TRs) to achieve high power density. The output matching network is initially designed for a unit TR with a high impedance transformation ratio of 114 and then expanded to a 16-way binary power combining circuit. RC stabilizers with shunt inductors are tailored in the input and interstage matching networks to address the very low input impedance of the drive stage TRs. These stabilizers effectively increase the input impedance of the TRs. The bias circuit is designed with a DC bus-bar structure, enhancing flexibility for large-scale power combining. The fabricated HPA demonstrated a maximum small-signal gain of 26.3 dB at 16.2 GHz and a 3-dB bandwidth ranging from 15.1 to 17.7 GHz. It also achieved an output power of 46.1 dBm (40.7 W) under pulsed operation from 16.0 to 16.75 GHz with a drain voltage of 28 V. When the drain voltage was increased to 32 V, it reached a maximum output power of 63 W at 16.5 GHz, demonstrating an excellent power density of 2.03 W/mm 2 per chip area.
1 January 2020 in IEEE Access
In this paper, a W-band mixer integrated circuit (IC) with high image rejection ratio (IRR) is presented, compensating for the amplitude and phase mismatches between the I and Q channels in the image rejection mixer (IRM) using RF buffer amplifiers. It is shown by analysis and simulation that the signal coupling between the I and Q channels in the IRM can generate mismatches which can severely degrade the IRR, even though other circuit components are symmetrically designed so as not to induce mismatches. The coupling between two channels can become serious, especially in millimeter-wave IRM ICs where the circuit components are laid out in close proximity to reduce the chip size. It is also shown that poor isolation of millimeter-wave couplers can seriously degrade IRR. In this work, we employ an RF buffer amplifier at the RF port of the resistive mixer to compensate for the amplitude and phase mismatches. The designed W-band IRM IC is fabricated in a 0.1-μm GaAs pHEMT process. Measurements show that the bias tuning of the RF buffer amplifiers can minimize the mismatches and improve the IRR by up to 35 dB at RF from 91 to 95 GHz at an IF of 50 MHz. The IRM exhibits an IRR of 19.2–47.9 dB with conversion loss of 7.9–9.2 dB, which belongs to the highest IRR among the reported IRMs in the W-band.
17 April 2023 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This paper proposes a modeling of the practical substrate thickness so that it is possible to accurately design by predicting the dielectric thickness that varies for each circuit of a multi-layer printed circuit board (PCB) in the manufacturing process. The amount of dielectric to be filled into the empty space of the pre-stacked metal layer varies depending on the ratio of pre-stacked metal to the entire area during the high-temperature and high-pressure process, so the dielectric thickness between the inner layer and the outer layer metal varies. When the patterns are complex and non-uniform in design, the difference in the ratio of the pre-stacked metal occurs between the entire area and the partial area of the strip. For this reason, the dielectric thicknesses are manufactured differently for each circuit. Therefore, this paper proposes a practical dielectric thickness equation and a reference area to calculate the copper foil residual ratio. To find the optimal reference area for calculating the copper foil residual ratio, microstrip lines with the same width and length but different ratios of the surrounding pre-stacked metal were analyzed. Finally, a dielectric thickness prediction equation is proposed, and verified not only on a multilayer substrate with a thickness of 40 μm but also with 20 μm to show that it is a highly reliable radio frequency (RF) modeling solution.
6 August 2024 in IEEE Access
An X -band harmonic-tuned oscillator integrated circuit (IC) with high power and efficiency is presented, utilizing gallium nitride (GaN) high electron mobility transistor (HEMT). It consists of a feedback and load network to provide optimal harmonic impedances while satisfying the oscillation condition at the fundamental frequency. The feedback network is synthesized from harmonic load-pull simulations and further simplified into a circuit comprising capacitors and transmission line, eliminating the inductors. This modification serves to reduce losses, which in turn improves output power and efficiency, while also reducing circuit area. The feedback network incorporates parallel resonant shunt stubs to enhance frequency selectivity and facilitate harmonic impedance matching, while also serving as a bias circuit. The oscillator, fabricated using a 250-nm GaN HEMT process, achieves a high output power of 35.0 dBm delivered to the load at 10.5 GHz, demonstrating a remarkable efficiency of 48.9% and excellent phase noise at −124.9 dBc/Hz with a 1 MHz offset. These results indicate a significant improvement in power and efficiency compared to previous X -band watt-level GaN oscillator ICs.
1 January 2026 in IEEE Access