This study focuses on understanding the dephosphorization behaviors in converter steelmaking process under different situations. When controlling the basicity of slag, Fe_tO content and bath temperature by single slag and double slag-slag remaining operation to blow ordinary P-containing hot metal, the equilibrium value of phosphorus ([P]_e) between hot metal and slag in the early stage of steelmaking is lower than 0.0068%, and the ratio of actual phosphorus content ([P]_r) to equilibrium value ([P]e) is less than 4.6. By using top-blown lime powde, dephosphorization efficiency of high phosphorus hot metal at the early stage was up to 93.8%, and [P]_r/[P]_e lowered to be 2.24. When lime slagging instead of the top-blown lime powder method was used, the dephosphorization effect is bad in the early stage of blowing the medium phosphorus hot metal by double slag process, and it leads to high material consumption and low productivity.

A Cellular Automaton-Finite Element (CAFE) model and a secondary dendrite arm spacing (SDAS) model are established to study the evolutionary behavior of the macrostructure and the secondary dendrites on a 295 × 2270 mm² slab cross-section of experimental steel, respectively. The relationship between the element content, SDAS, equiaxed crystal ratio (ECR) and macrosegregation in continuously cast experimental slabs was studied comprehensively. It is found that with the increase in carbon content, the ECR increases at first and then decreases, and the ECR reaches the maximum value when the carbon content is 0.3%. With the increase in carbon content, the SDAS and average grain size of the equiaxed crystal zone increase, whereas the Si and Al content evidently affects the SDAS and average grain size of the equiaxed crystal zone to a greater extent than the Mn content. In addition, the SDAS can be reduced by reducing the content of C and Si within the acceptable range of alloy composition.

Heavy reduction (HR) is an effective technique to control V segregation in continuous casting bloom, but the effect of segregation improvement is limited by the parameters such as reduction position and reduction amounts. In order to improve the macrosegregation of bloom, numerical simulation and plant experiments are adopted in this research. A heat transfer model and a reduction model with comprehensive thermo-physical parameters were established. The two models were verified by comparing the measured surface temperature and the theoretical strain at the solidification front. It is determined that the position of the HR of the bearing steel bloom is 20.82 m~24.97 m from the meniscus, and the solid fraction in the center of the bloom is 0.6~1. The total reduction of the HR is set to 30 mm, and the reduction of each roller in the reduction range is set to 4 mm, 5 mm, 9 mm, 7 mm, and 5 mm, respectively, to prevent the formation of internal cracks. Plant trials were conducted to verify the effect of the optimized HR. The results show that the carbon segregation degree on the V channel and non-channel of the bloom decreases from 1.2 to 1.16 and increases from 0.93 to 0.95, respectively, and the central carbon segregation degree decreases from 1.17 to 1.15. Meanwhile, the internal crack was not found in the bloom.

Based on the solidification heat transfer model and the CAFE model, the solidification behavior and structure of 2311 die steel, with a cross-section dimension of 415 × 2270 mm at different casting speeds, specific water flow and superheat, is numerically simulated. Nail-shooting and acid-etching experiments are carried out on the slab to verify the model’s macroscopic size. With the increase in casting speed, the slab’s central equiaxed grain ratio (ECR) decreases and the average grain size increases. The increase in superheat promotes the growth of columnar grains and inhibits the growth of central equiaxed grains. When the superheat increases from 23 to 38 K, the ECR decreases from 43.2 to 29.64%, and the average radius of grains increases from 0.89 to 1.01 mm. With the increase in specific water flow, the ECR decreases, and the average grain radius is the smallest when the specific water content is 0.32 L kg⁻¹. Finally, the slab quality is improved by process optimization, and the central segregation index of carbon decreases from mean value of 1.15 to 1.05.

The solidification structure characteristics are decisive for the production of extra-thick slabs. This study developed a solidification heat transfer model and a cellular automaton–finite element coupled model to investigate the solidification behavior and structure characteristics of a 475 mm extra-thick slab. The models were applied under various continuous casting process parameters and different alloy element content. The simulation results reveal that casting speed has the most significant effect on the solidification behavior of extra-thick slabs, surpassing the impact of specific water flow and superheat. The solidification structure characteristics of the 475 mm extra-thick slabs were investigated under various conditions. The findings indicate that at higher casting speeds and superheats, the average grain size increases and the grain number decreases. The average grain size initially decreases and then increases with the rise in specific water flow, reaching its minimum at approximately 0.17 L·kg⁻¹. Additionally, the average grain radius first decreases and then slightly increases with an increase in carbon content, achieving the minimum value of about 0.17% carbon. Compared with carbon and manganese, silicon has a greater impact on the solidification structure of ultra-thick slabs, and a moderate increase in silicon content can effectively refine the grain size. This study provides a theoretical foundation for understanding the changes in solidification structure characteristics and optimizing continuous casting process parameters for 475 mm extra-thick slabs.