Heavy reduction (HR) is an effective technique to control V segregation in continuous casting bloom, but the effect of segregation improvement is limited by the parameters such as reduction position and reduction amounts. In order to improve the macrosegregation of bloom, numerical simulation and plant experiments are adopted in this research. A heat transfer model and a reduction model with comprehensive thermo-physical parameters were established. The two models were verified by comparing the measured surface temperature and the theoretical strain at the solidification front. It is determined that the position of the HR of the bearing steel bloom is 20.82 m~24.97 m from the meniscus, and the solid fraction in the center of the bloom is 0.6~1. The total reduction of the HR is set to 30 mm, and the reduction of each roller in the reduction range is set to 4 mm, 5 mm, 9 mm, 7 mm, and 5 mm, respectively, to prevent the formation of internal cracks. Plant trials were conducted to verify the effect of the optimized HR. The results show that the carbon segregation degree on the V channel and non-channel of the bloom decreases from 1.2 to 1.16 and increases from 0.93 to 0.95, respectively, and the central carbon segregation degree decreases from 1.17 to 1.15. Meanwhile, the internal crack was not found in the bloom.

Based on the thermal-mechanical coupling model, the distance from the critical position of the shrinkage cavity formation of the two bearing steel blooms to the meniscus is 22 and 19.78 m, respectively, and the critical center solid fraction is 0.7145 and 0.7033, respectively. Furthermore, the effects of superheat and casting speed on the critical value of shrinkage cavity formation are discussed. The results show that the two factors have a great influence on the critical position of shrinkage cavity formation in the former, but basically do not affect the critical solid fraction of shrinkage cavity formation. Finally, the industrial heavy reduction tests in different reduction intervals were carried out, and the results show that when the initial reduction position of the heavy reduction process is set before the critical solid fraction, it can not only eliminate the central shrinkage cavity of the bloom, but also improve the central segregation.

The evolution process of corner temperatures for a typical micro-alloyed steel S355 is numerically simulated under various working conditions. The microstructure near the corner cracks of the S355 slab is experimentally examined, and the austenite/ferrite transformation temperatures of S355 steel during heating and cooling are measured. The results indicate that the right-angle slab corner temperature at the exit of the mould rapidly decreased to below Ar₃ under intensive cooling in the foot roller zone. The film-like ferrite began to precipitate along the austenite grain boundary at the slab corner. The transformation from ferrite to austenite cannot be fully realized because the corner temperature cannot be quickly returned to Ac₃ or higher. The slab transverse corner cracks occur along the film-like ferrite during the bending process. The chamfered slab, which modifies the original right angle of the slab into the 30° chamfered angle with a chamfered length of 60 mm, can significantly weaken the heat transfer and cooling effect of the slab corner. The chamfered slab corner temperature always remained above Ar₃ during the bending and straightening processes. Precipitation of the pro-eutectoid film-like ferrite along the grain boundary cannot occur during cooling for the chamfered slab. The chamfered slab can keep the corner temperature above Ar3 and effectively avoid the occurrence of transverse corner cracks caused by grain boundary embrittlement.

In this paper, a new mechanical vibration technology applied to continuous casting production is studied, which is used to break the dendrite at the solidification front, expand the equiaxed dendrite zone, and improve the center quality of the billet. The exciting force of this vibration technology is provided by a new type of vibration equipment (Vibration roll) independently developed and designed. Firstly, an investigation is conducted into the impacts of vibration acceleration, vibration frequency, and the contact area between the Vibration roll (VR) and the billet surface on the internal stress distribution within the billet shell, respectively. Secondly, the billet with and without vibration treatment was sampled and analyzed through industrial tests. The results show that the area ratio of equiaxed dendrites in transverse specimens treated with vibration technology was 11.96%, compared to 6.55% in untreated specimens. Similarly, for longitudinal samples, the linear ratio of equiaxed dendrites was observed to be 34.56% in treated samples and 22.95% in untreated samples. Compared to the specimens without mechanical vibration, the billet treated with mechanical vibration exhibits an increase in the area ratio and linear ratio of equiaxed dendrite ratio by 5.41% and 11.61%, respectively. Moreover, the probability of bridging at the end of solidification of the billet treated by vibration technology was significantly reduced, and the central porosity and shrinkage cavities of the billet were significantly improved. This study provides the first definitive evidence that the novel mechanical vibration technology can enhance the quality of the billet during the continuous casting process.

The edge seam defect is a common defect in hot rolling heavy plates. It can be improved by optimizing the corner shapes of slabs. Based on a numerical analysis of the effects of the slab corner shape on the temperature distribution after the slab’s exit from the heating furnace, three rolling methods are proposed for controlling the two-chamfered slab corner shape. The stress and deformation of the corner of the slab during the two-chamfered rolling process are investigated using a numerical simulation. The results show that a two-chamfered shape slab has the smallest temperature drop during the cooling process, and the slab corner can maintain higher temperature and uniformity, which is beneficial for controlling the deformation during the rolling process. Among the three kinds of two-chamfered rolling methods, frontal rolling using a two-roller has the smallest rolling force and rolling resistance to the casting machine, followed by horizontal rolling and then vertical rolling, which has the largest. The favorable slab corner in a two-chamfered shape can be obtained by frontal rolling using a two-roller. Industrial trials confirm that an edge seam defect rate of less than 5% in heavy plates can be achieved under the condition of a large broadside ratio.