Purpose: Passive conducting elements are the important parts of textronic systems. This paper aims to study a possibility of creating well-conducting and durable elements in textile materials by combining two technologies – physical vapour deposition (PVD) and laser patterning. Design/methodology/approach: Thin conducting metallic layers on common fabrics do not provide satisfactory resistance to bending and stretching; therefore, selected textile composite materials have been proposed as a substrate. The conducting elements were produced in two stage process – deposition of thin metallic layer on textile composite and creating conducting elements by laser patterning. Laser ablation process was optimized using modelling in Comsol Multiphysics package. Properties of conducting structures were investigated experimentally and by modelling. Findings: This paper confirms the correctness of the choice of the textile composite as a substrate for conducting elements. The results have shown that combining PVD deposition of thin metallic layer and controlled laser ablation allow creating passive elements such as resistors, inductive coils and heaters. Computer simulations conducted in the Comsol Multihysics environment enabled to determine the temperature distribution around the heaters and to describe the dynamics of its changes. The obtained results allow to shorten time of the optimization process of structures with different geometry and assumed temperature distribution. Originality/value: The novelty of this research can be summarized as following: choosing of textile composites as substrates for conductive elements instead of textiles used so far in textronics; creating conductive structures on textile composites using combined technologies, PVD and laser patterning, for the first time; modelling of laser ablation process of thin metallic layer; and optimization of properties of conducting elements by computer modelling.

This paper describes a method of laser ablation for improving the hydrophobic properties of vulcanized rubber. The treatment was tested on acrylonitrile rubber (NBR) and styrene butadiene rubber (SBR) containing carbon nanotubes and soot as fillers. The surface layer of the vulcanizates was modified using a nanosecond-pulsed laser at 1060 nm wavelength. The parameters of the ablation process were congruent, so no chemical changes in the polymeric material were observed. Evaluation of the surface condition of the laser-textured samples was performed using a Leica MZ6 stereoscopic microscope, operating with MultiScan 8.0 image analysis software. The contact angles were determined for all the samples before and after the surface modification process. Following modification of the surface morphology, with the best parameters of laser ablation, the contact angle increased, reaching 147°, which is very close to the threshold of superhydrophobicity (150°). On the basis of the results from several tests, laser ablation with a fiber-pulsed laser can be considered a very useful method for producing rubbers with superhydrophobic surfaces.

The main aim of this paper is to analyze the influence of laser shaping of the photovoltaic cell based on its efficiency. The authors described both process of the monocrystalline photovoltaic cell manufacturing, its efficiency, and the possibilities of usage in architecture and the process of creating the photovoltaic cells of unconventional shapes by using laser technology. A method for cutting photovoltaic cells using a fiber laser was presented as well as the parameters of the laser cutting process. The described method allows cutting the massively produced silicon cells according to the predetermined trajectory. Using the proposed process parameters, satisfactory cutting edge quality, and negligible impact of the laser beam on changes in the structure of the photovoltaic cell active layers were achieved. In each cycle of structure cutting, only a small part of the material is removed (from 1 to 2 μm), and depending on the thickness, the process is repeated from 50 to 300 times. It has been shown that the efficiency of the modified cells depends on the ratio of their surface area to the laser cutting line.

The article presents significant results in research on creating superhydrophobic properties of materials which can be used as an interesting material for use in self-cleaning polymer protective gloves and similar applications where the superhydrophobicity plays a significant role. In this work the influence of laser surface modification of MVQ silicone rubber was investigated. The research was conducted using a nanosecond-pulsed laser at 1060 nm wavelength. After a process of laser ablation, the surface condition was examined using a SEM microscope and infrared spectroscopy. During the tests, the contact angle was checked both before and after the laser modification of samples pre-geometrised in the process of their production. The test results presented in the paper indicate that the chemical and physical modifications contribute to the change in the MVQ silicone rubber contact angle. A significant increase (by more than 30°) in the contact angle to 138° was observed. It was confirmed that surface geometrisation is not the only factor contributing to an increase in the contact angle of the analyzed material; other factors include a change in laser texturing parameters, such as mean beam power, pulse duration, scanning speed and pulse repetition frequency.

The aim of the study was to evaluate the effects of laser texturing of coated textile materials on their cut resistance. The investigated material was an aramid knitted fabric coated with a polymer layer made of an acrylic-styrene dispersion functionalized with particles of silicon carbide (SiC). The distribution of SiC particles in the coating microstructure was assessed on the basis of microscopic observations (scanning electron microscopy). The coating was laser textured, and then the cut resistance of the assembly was determined using a rectangular blade. The findings showed that laser texturing improved the cut resistance of the tested materials, causing a fourfold increase in that parameter as compared to non-modified textile materials. This fact may improve the safety of workers wearing protective gloves in terms of cut protection.