Diverse conditions in power systems, such as massive use of nonlinear loads, continuous switching and operation of large electrical loads, and the integration of renewable energies, among others, have adversely affected the power quality (PQ) because they produce undesirable distortions in the waveforms of voltage and current. The conventional way to quantify the PQ is using the PQ indices (PQIs). Yet, the nonstationary properties of voltage and current signals degrade the PQIs estimation whenever classical techniques are used. In this paper, a methodology based on single-sideband modulation method and the Wavelet and Hilbert transforms for the estimation of instantaneous PQIs is proposed. It is shown that the proposal yields better tracking of transitory changes in the voltage/current signals than classical techniques such as the short-time Fourier transform. The PQIs used are the root-mean-square values, frequency, total harmonic distortion, active power, reactive power, apparent power, distortion power, power factor, and total power factor. PQIs performance is validated using synthetic and real signals.

With the growing demand for sustainable energy solutions, biomass torrefaction has emerged as a crucial technology for converting agricultural waste into high-value biofuels. This work develops dual kinetic modeling using global and individual parameters combined using particle swarm optimization (PSO) to predict energy densification based on elemental composition (CHNO) and high heating values (HHVs). The global parameters are calculated from experiments conducted at 250 °C, 275 °C, and 300 °C, and the individual parameters are obtained by adjusting experimental points at each temperature. A two-step kinetic model was used and optimized to achieve exceptional adjustment accuracy (98.073–99.999%). The experiments were carried out in an inert atmosphere of nitrogen with a heating rate of 20 °C/min and a 100 min residence time. The results obtained demonstrate a crucial trade-off: while individual parameters provide superior accuracy (an average fit of 99.516%) for predicting degradation by weight loss, global parameters offer better predictions for elemental composition, with average errors of 2.129% (carbon), 1.038% (hydrogen), 9.540% (nitrogen), and 3.997% (oxygen). Furthermore, it has been found that by determining the kinetic parameters at a torrefaction temperature higher than the maximum peak observed in the derivative thermogravimetric (DTG) curve (275 °C), it is possible to predict the behavior of the process within the 250–325 °C range with an R-squared value corresponding to an error lower than 3%. This approach significantly reduces the number of required experiments from twelve to only four by relying on a single isothermal condition for parameter estimation.

Phasor measurement units (PMUs) are important elements in power systems to monitor and know the real network condition. In order to regulate the performance of PMUs, the IEEE Std. C37.118.1 stablishes two classes—P and M, where the phasor estimation is carried out using a quadrature oscillator and a low-pass (LP) filter for modulation and demodulation, respectively. The LP filter plays the most important role since it determines the accuracy, response time and rejection capability of both harmonics and aliased signals. In this regard and by considering that the M-class filters are used for more accurate measurements, the IEEE Std. presents different M-class filters for different reporting rates (when a result is given). However, they can degrade their performance under frequency deviations if the LP frequency response is not properly considered. In this work, a unified model for magnitude compensation under frequency deviations for all the M-class filters is proposed, providing the necessary values of compensation to improve their performance. The model considers the magnitude response of the M-class filters for different reporting rates, a normalized frequency range based on frequency dilation and a fitted two-variable function. The effectiveness of the proposal is verified using both static and dynamic conditions for frequency deviations. Besides that, a real-time simulator to generate test signals is also used to validate the proposed methodology.

The global transition toward carbon-neutral energy solutions has established Solid Oxide Fuel Cells (SOFCs) as a key technology for next-generation power generation. This work presents a comprehensive numerical study and multi-factor statistical analysis of an anode-supported SOFC fueled by synthetic diesel. A three-dimensional computational fluid dynamics model, validated against experimental data, was integrated with a Taguchi L₂₇ orthogonal array to systematically evaluate the influence of six key parameters: temperature, fuel mass flow rate, operating pressure, current load, flow channel configuration, and methane molar fraction. Statistical analysis through the signal-to-noise ratio and analysis of variance identified the operating current as the most significant factor affecting cell voltage, followed by the fuel mass flow rate and temperature. The experiments showed that the highest levels of all factors (except for the current, which had the lowest level) maximize electrochemical performance while maintaining a steam-to-carbon ratio (S/C) within a range of 0.83 to 0.92, calculated based on total carbon content, ensuring sufficient humidification for internal reforming across all tested fuel compositions. Furthermore, a multiple linear regression model was developed as a computationally efficient surrogate, demonstrating exceptional predictive accuracy with an R² of 0.9954 and a mean relative error of 1.76% across independent validation cases. These results provide a robust methodology for rapid design and sensitivity analysis of internal-reforming SOFCs, offering a precise tool for optimizing fuel utilization in high-temperature electrochemical systems.

Biofuels represent a sustainable alternative that supports global energy development without compromising environmental balance. This work introduces a novel hardware–software platform for the experimental characterization of biomass solid yield during the slow pyrolysis process, integrating physical experimentation with advanced computational modeling. The hardware consists of a custom-designed pyrolizer equipped with temperature and weight sensors, a dedicated control unit, and a user-friendly interface. On the software side, a two-step kinetic model was implemented and coupled with three optimization algorithms, i.e., Particle Swarm Optimization (PSO), Genetic Algorithm (GA), and Nelder–Mead (N-M), to estimate the Arrhenius kinetic parameters governing biomass degradation. Slow pyrolysis experiments were performed on wheat straw (WS), pruning waste (PW), and biosolids (BS) at a heating rate of 20 °C/min within 250–500 °C, with a 120 min residence time favoring biochar production. The comparative analysis shows that the N-M method achieved the highest accuracy (100% fit in estimating solid yield), with a convergence time of 4.282 min, while GA converged faster (1.675 min), with a fit of 99.972%, and PSO had the slowest convergence time at 6.409 min and a fit of 99.943%. These results highlight both the versatility of the system and the potential of optimization techniques to provide accurate predictive models of biomass decomposition as a function of time and temperature. Overall, the main contributions of this work are the development of a low-cost, custom MATLAB-based experimental platform and the tailored implementation of optimization algorithms for kinetic parameter estimation across different biomasses, together providing a robust framework for biomass pyrolysis characterization.

In this work we present a form to get soliton pulses using a fiber Bragg-grating based on a Gires-Tournois interferometer (FBGGTI) as control medium for dispersion and nonlinearities. The interferometer is conformed by two Bragg-gratings, one of them as a weak grating, and the other one as a strong one, spaced by 4 mm of distance. Inside the setup, a "sech" profile as apodization type is used, to generate fundamental solitons. The results show that when Gaussian profile pulses are launched into this device fundamentals solitons, that are excellent for communication systems, are obtained.