Although induction motors (IMs) are robust and reliable electrical machines, they can suffer different faults due to usual operating conditions such as abrupt changes in the mechanical load, voltage, and current power quality problems, as well as due to extended operating conditions. In the literature, different faults have been investigated; however, the broken rotor bar has become one of the most studied faults since the IM can operate with apparent normality but the consequences can be catastrophic if the fault is not detected in low-severity stages. In this work, a methodology based on convolutional neural networks (CNNs) for automatic detection of broken rotor bars by considering different severity levels is proposed. To exploit the capabilities of CNNs to carry out automatic image classification, the short-time Fourier transform-based time–frequency plane and the motor current signature analysis (MCSA) approach for current signals in the transient state are first used. In the experimentation, four IM conditions were considered: half-broken rotor bar, one broken rotor bar, two broken rotor bars, and a healthy rotor. The results demonstrate the effectiveness of the proposal, achieving 100% of accuracy in the diagnosis task for all the study cases.

One of the most critical devices in an electrical system is the transformer. It is continuously under different electrical and mechanical stresses that can produce failures in its components and other electrical network devices. The short-circuited turns (SCTs) are a common winding failure. This type of fault has been widely studied in literature employing the vibration signals produced in the transformer. Although promising results have been obtained, it is not a trivial task if different severity levels and a common high-level noise are considered. This paper presents a methodology based on statistical time features (STFs) and support vector machines (SVM) to diagnose a transformer under several SCTs conditions. As STFs, 19 indicators from the transformer vibration signals are computed; then, the most discriminant features are selected using the Fisher score analysis, and the linear discriminant analysis is used for dimension reduction. Finally, a support vector machine classifier is employed to carry out the diagnosis in an automatic way. Once the methodology has been developed, it is implemented on a field-programmable gate array (FPGA) to provide a system-on-a-chip solution. A modified transformer capable of emulating different SCTs severities is employed to validate and test the methodology and its FPGA implementation. Results demonstrate the effectiveness of the proposal for diagnosing the transformer condition as an accuracy of 96.82% is obtained.

Data mining is a technological and scientific field that, over the years, has been gaining more importance in many areas, attracting scientists, developers, and researchers around the world. The reason for this enthusiasm derives from the remarkable benefits of its usefulness, such as the exploitation of large databases and the use of the information extracted from them in an intelligent way through the analysis and discovery of knowledge. This document provides a review of the predictive data mining techniques used for the diagnosis and detection of faults in electric equipment, which constitutes the pillar of any industrialized country. Starting from the year 2000 to the present, a revision of the methods used in the tasks of classification and regression for the diagnosis of electric equipment is carried out. Current research on data mining techniques is also listed and discussed according to the results obtained by different authors.

Currently, renewable energies, including wind energy, have been experiencing significant growth. Wind energy is transformed into electric energy through the use of wind turbines (WTs), which are located outdoors, making them susceptible to harsh weather conditions. These conditions can cause different types of damage to WTs, degrading their lifetime and efficiency, and, consequently, raising their operating costs. Therefore, condition monitoring and the detection of early damages are crucial. One of the failures that can occur in WTs is the occurrence of cracks in their blades. These cracks can lead to the further deterioration of the blade if they are not detected in time, resulting in increased repair costs. To effectively schedule maintenance, it is necessary not only to detect the presence of a crack, but also to assess its level of severity. This work studies the vibration signals caused by cracks in a WT blade, for which four conditions (healthy, light, intermediate, and severe cracks) are analyzed under three wind velocities. In general, as the proposed method is based on machine learning, the vibration signal analysis consists of three stages. Firstly, for feature extraction, statistical and harmonic indices are obtained; then, the one-way analysis of variance (ANOVA) is used for the feature selection stage; and, finally, the k-nearest neighbors algorithm is used for automatic classification. Neural networks, decision trees, and support vector machines are also used for comparison purposes. Promising results are obtained with an accuracy higher than 99.5%.

Sudden cardiac death (SCD) is a global health problem, which represents 15–20% of global deaths. This type of death can be due to different heart conditions, where ventricular fibrillation has been reported as the main one. These cardiac alterations can be seen in an electrocardiogram (ECG) record, where the heart’s electrical activity is altered. The present research uses these variations to be able to predict 30 min in advance when the SCD event will occur. In this regard, a methodology based on the complete ensemble empirical mode decomposition (CEEMD) method to decompose the cardiac signal into its intrinsic mode functions (IMFs) and a convolutional neural network (CNN) for automatic diagnosis is proposed. Results for the ensemble empirical mode decomposition (EEMD) method and the empirical mode decomposition (EMD) method are also compared. Results demonstrate that the combination of the CEEMD and the CNN is a potential solution for SCD prediction since 97.5% of accuracy is achieved up to 30 min in advance of the SCD event.

High performance, highly efficient DC-DC converters play a key role in improving the penetration of renewable energy sources in the context of smart grids in applications such as solid-state transformers, built-in power drives in electric vehicles and interfacing photovoltaic and wind-power systems. Advanced medium-frequency transformers (MFTs) are fundamental to enhance DC-DC converters and determining its behavior, therefore MFT design procedures have become increasingly important in this context. This paper investigates which type of core material, between nanocrystalline and silicon steel, has the best properties for designing MFTs for distinct applications. Unlike to other proposals, in this work, two 1 kVA-120 V/240 V-1 kHz lab MFT prototypes, with a different type of core material, are developed for the purpose of comparing its physical characteristics, behavior, and performance under real-life conditions. A final section, the experimental results show that the nanocrystalline MFT has greater power density and efficiency. The results of this work introduce nanocrystalline MFTs as an option in a wider range of applications in niches in which other materials are currently used.