Limitations of access have long restricted exploration and investigation of the cavities beneath ice shelves to a small number of drillholes. Studies of sea-ice underwater morphology are limited largely to scientific utilization of submarines. Remotely operated vehicles, tethered to a mother ship by umbilical cable, have been deployed to investigate tidewater-glacier and ice-shelf margins, but their range is often restricted. The development of free-flying autonomous underwater vehicles (AUVs) with ranges of tens to hundreds of kilometres enables extensive missions to take place beneath sea ice and floating ice shelves. Autosub2 is a 3600 kg, 6.7 m long AUV, with a 1600 m operating depth and range of 400 km, based on the earlier Autosub1 which had a 500 m depth limit. A single direct-drive d.c. motor and five-bladed propeller produce speeds of 1–2 m s−1. Rear-mounted rudder and stern-plane control yaw, pitch and depth. The vehicle has three sections. The front and rear sections are free-flooding, built around aluminium extrusion space-frames covered with glass-fibre reinforced plastic panels. The central section has a set of carbon-fibre reinforced plastic pressure vessels. Four tubes contain batteries powering the vehicle. The other three house vehicle-control systems and sensors. The rear section houses subsystems for navigation, control actuation and propulsion and scientific sensors (e.g. digital camera, upward-looking 300 kHz acoustic Doppler current profiler, 200 kHz multibeam receiver). The front section contains forward-looking collision sensor, emergency abort, the homing systems, Argos satellite data and location transmitters and flashing lights for relocation as well as science sensors (e.g. twin conductivity–temperature–depth instruments, multibeam transmitter, sub-bottom profiler, AquaLab water sampler). Payload restrictions mean that a subset of scientific instruments is actually in place on any given dive. The scientific instruments carried on Autosub are described and examples of observational data collected from each sensor in Arctic or Antarctic waters are given (e.g. of roughness at the underside of floating ice shelves and sea ice).
A miniature high precision conductivity and temperature (CT) sensor system has been developed for ocean salinity monitoring. The CT sensor is manufactured using micro fabrication technology. A novel seven-electrode conductivity cell has been developed which has no field leakage. This is combined with a platinum resistor temperature bridge to produce an integrated CT sensor. A generic impedance measurement circuit has been developed, with three-parameter sine fitting algorithm. It has a 1 month battery life at 10 s sampling interval. Calibration results show that the initial CT accuracies are ±0.03 mS/cm and ±0.01°C, respectively. Testing of the CT sensor has been performed in the north Atlantic and revealed drift in sensor readings after five weeks of operation.
15 August 2019 in Journal of Geophysical Research: Oceans
A new method for the detection of sea ice using GNSS‐R (Global Navigation Satellite Systems Reflectometry) is presented and applied to 33 months of data from the U.K. TechDemoSat‐1 mission. This method of sea ice detection shows the potential for a future GNSS‐R polar mission, attaining an agreement of over 98% and 96% in the Antarctic and Arctic, respectively, when compared to the European Space Agency's Climate Change Initiative sea ice concentration product. The algorithm uses a combination of two parameters derived from the delay‐Doppler Maps to quantify the spread of power in delay and Doppler. Application of thresholds then allows sea ice to be distinguished from open water. Differences between the TechDemoSat‐1 sea ice detection and comparison data sets are explored. The results provide information on the seasonal and multiyear changes in sea ice distribution of the Arctic and Antarctic. Future potential and applications of this technique are discussed.
During its commissioning phase, the Copernicus Sentinel-3B satellite has been placed in a tandem formation with Sentinel-3A for a period of 6 months. This configuration allowed a direct comparison of measurements obtained by the two satellites. The purpose of this paper was to present the range of analyses that can be performed from this dataset, highlighting methodology aspects and the main outcomes for each instrument. We examined, in turn, the benefit of the tandem in understanding instrument operational modes differences, in assessing inter-satellite differences, and in validating measurement uncertainties. The results highlighted the very good consistency of the Sentinel-3A and B instruments, ensuring the complete inter-operability of the constellation. Tandem comparisons also pave the way for further improvements through harmonization of the sensors (OLCI), correction of internal stray-light sources (SLSTR), or high-frequency processing of SRAL SARM data. This paper provided a comprehensive overview of the main results obtained, as well as insights into some of the results. Finally, we drew the main lessons learned from the Sentinel-3 tandem phase and provided recommendations for future missions.
The first digital elevation model (DEM) of the Antarctic ice sheet derived from Global Navigation Satellite Systems‐Reflectometry (GNSS‐R) data from the UK TechDemoSat‐1 satellite is presented. This is obtained using 32 months of data from the mission. This opportunistic and inexpensive method is shown to produce encouraging results from the technology demonstration platform of TechDemoSat‐1, with median bias under 18 m and root‐mean‐square difference under 91 m when compared to the CryoSat‐2 1‐km DEM v1.0. Discrepancies between the two data sets are explored along with possible causes of such differences and potential improvements to further optimize this technique for future GNSS‐R missions.