This paper presents the design of a printed step-type monopole antenna for biological tissue analysis and medical imaging applications in the microwave frequency range. The design starts from a very simple and widely known rectangular monopole antenna, and different modifications to the antenna geometry are made in order to increase the bandwidth. The antenna dimensions are optimized by means of a parametric analysis of each dimension using a 3-D electromagnetic simulator based on the finite element method. The optimized antenna, with final dimensions of 40 × 36 mm², is manufactured onto a low-cost FR4 (fiber glass epoxy) substrate. The characteristics of the antenna have been measured inside an anechoic chamber, obtaining an omnidirectional radiation pattern and a working frequency range between 2.7 GHz and 11.4 GHz, which covers the UWB frequencies and enables the use of the antenna in medical imaging applications. Finally, the behaviour of four of these antennas located around a realistic breast model, made with biocompatible materials, has been analysed with the electromagnetic simulator, obtaining good results and demonstrating the usefulness of the designed antenna in the proposed application.

This work introduces a microwave-based system able to detect tumours in breast phantoms in a non-invasive way. The data acquisition system is composed of a hardware system which involves high-frequency components (antennas, switches and cables), a microcontroller, a vector network analyser used as measurement instrument and a computer devoted to the control and automation of the operation of the system. Concerning the software system, the computer runs a Python script which is in charge of mastering and automatising all the required stages for the data acquisition, from initialisation of the hardware system to performing and saving the measurements. We also report on the design of the high-performance broadband antenna used to carry out the measurements, as well as on the algorithm employed to build the final medical images, based on an adapted version of the so-called Improved Delay-and-Sum (IDAS) algorithm improved by a Hamming window filter and averaging preprocessing. The calibration and start-up of the system are also described. The experimental validation includes the use of different tumour models with different dielectric properties inside the breast phantom. The results show promising tumour detection capabilities, even when there is low dielectric contrast between the tumoural and healthy tissues, as is the usual case for dense breasts in young women.

Direct ink writing (DIW) of conductive ink is a printed electronics technology that allows a variety of electronic circuits to be produced in a simple way and with minimal waste of materials. In recent years it has been used for rapid prototyping of RF circuits typically working at S-band frequencies (2–4 GHz). In an attempt to extend this frequency range while maintaining cost-effective prototyping, this work has focused on proving the feasibility of DIW of silver-conductive (SC) ink for the fabrication of planar microwave circuits beyond 10 GHz, more specifically, ultra-wideband (UWB) antennas for medical applications. For this purpose, the DC and RF performance of the SC ink, as well as the FR4 substrate used, were first evaluated. Based on the comparison between experimental and simulated results, we have found that the effective RF conductivity of the SC ink is approximately 27.6% of its DC value and 3.4% of the copper conductivity. A few test microstrip circuits were fabricated by DIW, namely two S-band filters and one UWB antenna. The overall measured performance of all of them agreed well with simulations. In particular, the DIW antenna exhibited a bandwidth of 8.2 GHz (between 2.4 and 10.6 GHz), and was compared with an identical copper antenna showing that both have very similar characteristics. It was also found that the lower conductivity of SC ink as compared to copper led to a gain reduction of only 0.3 dB.

This work shows a proof of concept of a radar-based microwave imaging system for the detection of the brain-shift effect with minimum delay. The system is based on the estimation of the variations of both the position and the geometry of the brain in order to detect if remarkable variations have occurred. To that end, the system makes use of 12 twin antennas as sensing elements, which transmit broadband signals towards the patient’s head and receive the corresponding reflections. Printed monopole antennas with coplanar feed are considered, featuring a broad bandwidth and an omnidirectional radiation pattern. A signal processing strategy to estimate the detected distances to the target from the reflection seen by each antenna is also shown, as well as a calibration and fine-tuning procedure for accurate distance detection capabilities. To demonstrate the potential of the system, a cranium phantom and several brain phantoms, emulating different brain-shift cases, are fabricated and measured. The results show the effective detection of the brain-shift in all the cases under consideration, thereby demonstrating the potential of microwave imaging systems for effective intraoperative brain-shift detection.

This work presents the validation of a low-cost measurement system based on an open-ended coaxial SMA (SubMiniature version A) probe for the characterization of complex permittivity in the microwave frequency range. The system combines a custom-fabricated probe, a vector network analyzer, and a dedicated software application that implements three analytical models: capacitive, radiation, and virtual transmission line models. A comprehensive experimental campaign was carried out involving pure polar liquids, saline solutions, and biological tissues, with the measurements compared against those obtained using a high-precision commercial probe. The results confirm that the proposed system is capable of delivering accurate and reproducible permittivity values up to at least 6 GHz. Among the implemented models, the radiation model demonstrated the best overall performance, particularly in biological samples. Additionally, reproducibility tests with three independently assembled SMA probes showed normalized deviations below 3%, confirming the robustness of the design. These results demonstrate that the proposed system constitutes a viable alternative for cost-sensitive applications requiring portable or scalable microwave dielectric characterization.

A radio frequency (RF)-based system for surgical navigation is presented. Surgical navigation technologies are widely used nowadays for aiding the surgical team with many interventions. However, the currently available options still pose considerable limitations, such as line-of-sight occlusion prevention or restricted materials and equipment allowance. In this work, we suggest a different approach based on a microwave broadband antenna system. We combine techniques from microwave medical imaging, which can overcome the current limitations in surgical navigation technologies, and we propose methods to develop RF-based systems for real-time tracking neurosurgical tools. The design of the RF system to perform the measurements is shown and discussed, and two methods (Multiply and Sum and Delay Multiply and Sum) for building the medical images are analyzed. From these measurements, a surgical tool’s position tracking system is developed and experimentally assessed in an emulated surgical scenario. The reported results are coherent with other approaches found in the literature, while overcoming their main practical limitations. The discussion of the results discloses some hints on the validity of the system, the optimal configurations depending on the requirements, and the possibilities for future enhancements.