The quasi-static and low cycle fatigue tests of extruded 7075 Al alloy (Φ200 mm) were investigated in three directions: the extrusion direction (ED), the radial direction (RD), and 45° with ED (45°). Grain morphology analysis, texture measurement, and fatigue fracture characterization were conducted to discuss the relationship between microstructure and mechanical properties. The experimental results showed that the ED specimen had higher ultimate tensile strength (UTS) and low cycle fatigue (LCF) properties, which were mainly attributed to the following three causes. First, the grain boundaries (GBs) had an obvious effect on the crack growth. The number of GBs in the three directions was different due to the shape of the grains elongated along the ED. Second, the sharp texture and the small Schmidt factor along the ED explained the higher ultimate tensile strength (UTS) of the ED specimens. Third, fatigue fracture observation showed that the ED specimen had a narrow fatigue striation spacing, which indicated that the plastic deformation of the ED specimen was the smallest in each cycle. In addition, two fatigue prediction models were established to predict the LCF life of extruded 7075 Al alloy, based on the life response behavior of the three directions under different strains.
11 April 2023 in Journal of Materials Research and Technology
For an extrusion process of 7075 Al alloy, the extrusion direction of the initial blank is changed to study the mechanical properties of the formed plates and characterize their microstructure. The as-received bar is extruded 7075 Al alloy. The secondary extrusion deformation is along and perpendicular to the initial extrusion direction. The results show that the anisotropy of mechanical properties of the two samples decreases obviously after secondary deformation. The anisotropy of yield strength and ultimate tensile strength of ED90 sample is lower than that of ED0 sample, but the plastic anisotropy is slightly higher than that of ED0 sample. In addition, the recrystallized grain proportion of ED90 sample is high and the texture strength is low, so the Schmid factor in the three directions is similar. The tensile fracture mode of the two samples belongs to ductile fracture, but the morphology of dimple and the size of cleavage plane are slightly different.
In this study, Mg-13Gd-4Y-2Zn-0.5Zr alloys were fabricated and subjected to 3 passes of cyclic expansion-extrusion with an asymmetrical cavity (CEE-AEC). The influence of the CEE-AEC together with the heat treatment on the microstructural characteristics and hardness were investigated systematically, through optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Vickers hardness testing machine. The results illuminated that the introduction of the strains through CEE-AEC has a significant effect on the heat treatment of the specimens. The precipitation of the second phases particles was remarkably accelerated, including the lamellar phases in solution treatment, the grain boundary precipitates and the equilibrium β phases in ageing treatment. Likewise, the hardness of the investigated samples was obviously improved by the comprehensive effect of the CEE-AEC together with the heat treatment, and the peak aging time of the CEE-AEC samples was substantially advanced relative to the as-cast ones. The enhanced hardness owned relatively high thermal stability in the ambient temperature. The precipitation sequence of 3 CEE-AEC passes alloy aged at 225 °C was as follows: supersaturated solid solution Mg (S.S.S.S)→β″ (DO19)→β′ (bco)→β1 (fcc)→β (fcc).
The superhydrophobic and highly oleophobic cotton textile was obtained by applying particle -based in situ fabrication procedure with the low toxic perfluoropolyether (PFPE) and the silica particles. The water contact angle and salad oil contact angle on the treated cotton textile surface can be achieved to 156.8 º and 143.3 º respectively. The microstructure of the treated cotton textile surface was revealed by scanning electron microscopy (SEM). And the chemical composition of the treated cotton textile surface was determined by the X-ray photoelectron spectroscopy (XPS) analysis. Thermogravimetric (TG) analysis showed that the weight loss of the treated cotton is less than that of the untreated sample.