Jin Ma

Jin Ma

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 August 2021 in Materials
Verified
Journal Article
Open access
PDF file
JMJin Ma
Jin Ma
QWQiang Wang
Qiang Wang
YYYongbiao Yang
Yongbiao Yang
FYFulai Yang
Fulai Yang
DBDong Beibei
Dong Beibei
ZZZhimin Zhang
Zhimin Zhang
The quasi-static and low cycle fatigue tests of extruded 7075 Al alloy (Φ200 mm) were investigated in three directions: the extrusion direction (ED), the radial direction (RD), and 45° with ED (45°). Grain morphology analysis, texture measurement, and fatigue fracture characterization were conducted to discuss the relationship between microstructure and mechanical properties. The experimental results showed that the ED specimen had higher ultimate tensile strength (UTS) and low cycle fatigue (LCF) properties, which were mainly attributed to the following three causes. First, the grain boundaries (GBs) had an obvious effect on the crack growth. The number of GBs in the three directions was different due to the shape of the grains elongated along the ED. Second, the sharp texture and the small Schmidt factor along the ED explained the higher ultimate tensile strength (UTS) of the ED specimens. Third, fatigue fracture observation showed that the ED specimen had a narrow fatigue striation spacing, which indicated that the plastic deformation of the ED specimen was the smallest in each cycle. In addition, two fatigue prediction models were established to predict the LCF life of extruded 7075 Al alloy, based on the life response behavior of the three directions under different strains.

16 January 2020 in Metals
Verified
Journal Article
Open access
PDF file
DBDong Beibei
Dong Beibei
ZZZhimin Zhang
Zhimin Zhang
XCXin Che
Xin Che
JMJin Ma
Jin Ma
MMMu Meng
Mu Meng
JZJinlu Zhang
Jinlu Zhang
The current work systematically investigated the microstructure, texture evolution, and mechanical properties of MDFed Mg-13Gd-4Y-2Zn-0.5Zr (wt%) alloy (GWZ) on the condition of high and low temperature cycle deformation. The high and low temperature cycle deformation was proposed on the basis of the conventional multi-directional forging (MDF) at decreasing temperature and annealing treatment. As a new method, it was aimed to timely uniform the microstructure and strengthen magnesium (Mg) matrix during the deformation process. A low accumulative strain of 3 after 1 pass resulted in a bimodal microstructure with undynamic recrystallized (unDRXed) regions and dynamic recrystallized (DRXed) grains, while a high accumulative strain of 12 after 4 passes lead to a homogeneous microstructure with fine DRXed grains. According to the experimental results, it indicated that the average grain size of 63 μm after homogenization treatment at 520 was refined remarkably to 5.20 μm after 4 passes at 420 °C through high and low temperature cycle deformation. The area fraction of DRXed grains was increased to 98.4%, which can be regarded as achieving complete DRX after 4 passes. The grain refinement was mainly caused by particle stimulation nucleation (PSN) and mechanism. As the MDF passes and accumulative strain increased, the basal texture was weakened and transformed from a strong basal texture to a random distribution gradually. Compared with conventional MDF at decreasing temperature, the mechanical properties were enhanced effectively. After 4 passes, the ultimate tensile strength (UTS), tensile yield strength (TYS), and failure elongation (FE) were 405 MPa, 305 MPa, and 13.1%, respectively.

12 October 2025 in Journal of Materials Science & Technology
Verified
Journal Article
Closed access
JMJin Ma
Jin Ma
FLF. Liu
F. Liu
JTJ. Tan
J. Tan
XLX.W. Li
X.W. Li

15 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
HCHui Cao
Hui Cao
YYYongbiao Yang
Yongbiao Yang
XZxing zhang
xing zhang
JMJin Ma
Jin Ma
TZTingyan Zhang
Tingyan Zhang
ZZZhimin Zhang
Zhimin Zhang
This study proposed a rotary back extrusion (RBE) process for an open punch, which is used to produce high-performance 7075 aluminum alloy cup-shaped piece. The RBE experiment was carried out on the Gleeble-3500 testing machine at 400 °C and compared with the conventional back extrusion (CBE). The microstructure was analyzed by optical microscope, scanning electron microscope and DEFORM-3D simulation software. The results shown that compared with CBE, RBE can significantly increase the equivalent strain value and deformation uniformity of 7075 aluminum alloy cup-shape pieces. RBE deformation increases the accumulated strain of the piece, and the rotation of the die causes the piece to produce shear strain, which increases the overall strain of the cup-shape piece. The proportion of dynamic recrystallization increases, and the grain refinement was obvious. The micro-hardness value of the RBE sample is higher than that of the CBE sample, which could be the result of grain refinement strengthening. What is more, RBE and CBE have different metal flow laws.

20 August 2020 in Materials
Verified
Journal Article
Open access
PDF file
XCXin Che
Xin Che
DBDong Beibei
Dong Beibei
KLKai Liu
Kai Liu
QWQiang Wang
Qiang Wang
MMMu Meng
Mu Meng
ZZZhimin Zhang
Zhimin Zhang
The rotating backward extrusion (RBE) process, as a new severe plastic deformation (SPD) process, is based on conventional backward extrusion and rotation, which meets the requirement of modern industrial development with its high performance and production efficiency. However, there is little research on the microstructure evolution and texture modification of the RBE process. Thus, in this study, the effect of different rotating revolutions, e.g., n = 5, n = 10, and n = 50, on the microstructure and texture development for the RBE process based on the AZ80 magnesium (Mg) alloy were investigated at 653 K. The results disclose that the rotating revolution is an influencing processing parameter on the deformation of the RBE process. The grain refining ability is enhanced with the increase of the rotating revolutions, and the minimum grain size of the cup bottom, shearing zone, and cup wall can reach to 16.7 μm, 15.6 μm, and 13.0 μm, respectively, under the condition of n = 50. Furthermore, with the increase in the rotating revolutions, the microstructure of the alloy becomes more uniform and the proportion of dynamic recrystallization (DRX) is also increased. The maximum DRX fractions of the sample for the cup bottom and cup wall are 95.4% and 86.8%, respectively, at n = 50. The DRX mechanism of the RBE process is determined by the continuous DRX and discontinuous DRX. In addition, the texture can be significant weakened during the RBE process, especially at the cup bottom, where the maximum pole intensity can be reduced from 17.6 at n = 10 to 6.5 at n = 50, which can be attributed to the higher proportion of new DRXed grains whose orientations are more random compared with the deformed grains.

1 January 2025 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
JMJin Ma
Jin Ma
FLF. Liu
F. Liu
JTJ. Tan
J. Tan
XLX.W. Li
X.W. Li