Zhimin Zhang

Prof. Zhimin Zhang

North University of China

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2020 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
BDBeibei Dong
Beibei Dong
ZZZhimin Zhang
Zhimin Zhang
JYJianmin Yu
Jianmin Yu
ZZZhimin Zhang
Zhimin Zhang
MMMu Meng
Mu Meng
JZJinlu Zhang
Jinlu Zhang

3 November 2020 in Materials
Verified
Journal Article
Open access
PDF file
GWGuoqin Wu
Guoqin Wu
JYJianmin Yu
Jianmin Yu
LJLeichen Jia
Leichen Jia
WXWenLong Xu
WenLong Xu
DBDong Beibei
Dong Beibei
BHBiying Hao
Biying Hao
Reciprocating Upsetting-Extrusion (RUE) deformation process can significantly refine the grains size and weaken the basal plane texture by applying a large cumulative strain to the alloy, which is of great significance to weaken the anisotropy of magnesium (Mg) alloys and increase the application range. In this paper, the Mg-8.27Gd-3.18Y-0.43Zr (wt %) alloy was subjected to isothermal multi-passes RUE. The microstructure and texture evolution, crystal orientation-dependent deformation mechanism of the alloy after deformation were investigated. The results clearly show that with the increase of RUE process, the grains are significantly refined through continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX) mechanisms, the uniformity of the microstructure is improved, and the texture intensity is reduced. At the same time, a large number of particle phases are dynamically precipitated during the deformation process, promoting grain refinement by the particle-stimulated nucleation (PSN) mechanism. The typical [10-10] fiber texture is produced after one pass due to the basal plane of the deformed grains with a relatively high proportion is gradually parallel to the ED during extrusion process. However, the texture concentration is reduced compared with the traditional extrusion deformation, indicating that the upsetting deformation has a certain delay effect on the subsequent extrusion texture generation. After three or four passes deformation, the grain orientation is randomized due to the continuous progress of the dynamic recrystallization process.

1 November 2021 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
BDBeibei Dong
Beibei Dong
XCXin Che
Xin Che
ZZZhimin Zhang
Zhimin Zhang
JYJianmin Yu
Jianmin Yu
MMMu Meng
Mu Meng

11 August 2021 in Materials
Verified
Journal Article
Open access
PDF file
JMJin Ma
Jin Ma
QWQiang Wang
Qiang Wang
YYYongbiao Yang
Yongbiao Yang
FYFulai Yang
Fulai Yang
DBDong Beibei
Dong Beibei
ZZZhimin Zhang
Zhimin Zhang
The quasi-static and low cycle fatigue tests of extruded 7075 Al alloy (Φ200 mm) were investigated in three directions: the extrusion direction (ED), the radial direction (RD), and 45° with ED (45°). Grain morphology analysis, texture measurement, and fatigue fracture characterization were conducted to discuss the relationship between microstructure and mechanical properties. The experimental results showed that the ED specimen had higher ultimate tensile strength (UTS) and low cycle fatigue (LCF) properties, which were mainly attributed to the following three causes. First, the grain boundaries (GBs) had an obvious effect on the crack growth. The number of GBs in the three directions was different due to the shape of the grains elongated along the ED. Second, the sharp texture and the small Schmidt factor along the ED explained the higher ultimate tensile strength (UTS) of the ED specimens. Third, fatigue fracture observation showed that the ED specimen had a narrow fatigue striation spacing, which indicated that the plastic deformation of the ED specimen was the smallest in each cycle. In addition, two fatigue prediction models were established to predict the LCF life of extruded 7075 Al alloy, based on the life response behavior of the three directions under different strains.

1 February 2022 in Materials Research Express
Verified
Journal Article
Open access
YZYi Zhang
Yi Zhang
JMJin Ma
Jin Ma
QWQiang Wang
Qiang Wang
YYYongbiao Yang
Yongbiao Yang
MZMingjie Zhu
Mingjie Zhu
ZZZhimin Zhang
Zhimin Zhang
For an extrusion process of 7075 Al alloy, the extrusion direction of the initial blank is changed to study the mechanical properties of the formed plates and characterize their microstructure. The as-received bar is extruded 7075 Al alloy. The secondary extrusion deformation is along and perpendicular to the initial extrusion direction. The results show that the anisotropy of mechanical properties of the two samples decreases obviously after secondary deformation. The anisotropy of yield strength and ultimate tensile strength of ED90 sample is lower than that of ED0 sample, but the plastic anisotropy is slightly higher than that of ED0 sample. In addition, the recrystallized grain proportion of ED90 sample is high and the texture strength is low, so the Schmid factor in the three directions is similar. The tensile fracture mode of the two samples belongs to ductile fracture, but the morphology of dimple and the size of cleavage plane are slightly different.

16 January 2020 in Metals
Verified
Journal Article
Open access
PDF file
DBDong Beibei
Dong Beibei
ZZZhimin Zhang
Zhimin Zhang
XCXin Che
Xin Che
JMJin Ma
Jin Ma
MMMu Meng
Mu Meng
JZJinlu Zhang
Jinlu Zhang
The current work systematically investigated the microstructure, texture evolution, and mechanical properties of MDFed Mg-13Gd-4Y-2Zn-0.5Zr (wt%) alloy (GWZ) on the condition of high and low temperature cycle deformation. The high and low temperature cycle deformation was proposed on the basis of the conventional multi-directional forging (MDF) at decreasing temperature and annealing treatment. As a new method, it was aimed to timely uniform the microstructure and strengthen magnesium (Mg) matrix during the deformation process. A low accumulative strain of 3 after 1 pass resulted in a bimodal microstructure with undynamic recrystallized (unDRXed) regions and dynamic recrystallized (DRXed) grains, while a high accumulative strain of 12 after 4 passes lead to a homogeneous microstructure with fine DRXed grains. According to the experimental results, it indicated that the average grain size of 63 μm after homogenization treatment at 520 was refined remarkably to 5.20 μm after 4 passes at 420 °C through high and low temperature cycle deformation. The area fraction of DRXed grains was increased to 98.4%, which can be regarded as achieving complete DRX after 4 passes. The grain refinement was mainly caused by particle stimulation nucleation (PSN) and mechanism. As the MDF passes and accumulative strain increased, the basal texture was weakened and transformed from a strong basal texture to a random distribution gradually. Compared with conventional MDF at decreasing temperature, the mechanical properties were enhanced effectively. After 4 passes, the ultimate tensile strength (UTS), tensile yield strength (TYS), and failure elongation (FE) were 405 MPa, 305 MPa, and 13.1%, respectively.