Practical wearable e‐textiles must be durable and retain, as far as possible, the textile properties such as drape, feel, lightweight, breathability, and washability that make fabrics suitable for clothing. Early e‐textile garments were realized by inserting standard portable electronic devices into bespoke pockets and arranging interconnects and cabling across the garment. In these examples, the textile merely served as a vehicle to house the electronics and had no inherent electronic functionality. A reduction in electronic component size, the development of flexible circuits, and the ability to weave robust interconnects offer the potential for improved levels of electronic integration within the textile. The weaving of electronic circuit filaments less than 2 mm wide into fabrics such that the electronics are fully concealed in the textile and given extra protection by the surrounding textile fibers is introduced. The failure mechanisms for different filament circuit designs before and after integration into the textile are investigated with a 90° cyclical bending test. Results show that encapsulated filament circuits embedded within the textile survive 45 washing cycles and more than 1500 cycles of 90° bending around a bending radius of 10 mm, performing five times better than equivalent filament circuits before integration into the fabric.
Temperature sensors are one of the most fundamental sensors and are found in industrial, environmental, and biomedical applications. The traditional approach of reading the resistive response of Positive Temperature Coefficient thermistors at DC hindered their adoption as wide-range temperature sensors. Here, we present a large-area thermistor, based on a flexible and stretchable short carbon fibre incorporated Polydimethylsiloxane composite, enabled by a radio frequency sensing interface. The radio frequency readout overcomes the decades-old sensing range limit of thermistors. The composite exhibits a resistance sensitivity over 1000 °C−1, while maintaining stability against bending (20,000 cycles) and stretching (1000 cycles). Leveraging its large-area processing, the anisotropic composite is used as a substrate for sub-6 GHz radio frequency components, where the thermistor-based microwave resonators achieve a wide temperature sensing range (30 to 205 °C) compared to reported flexible temperature sensors, and high sensitivity (3.2 MHz/°C) compared to radio frequency temperature sensors. Wireless sensing is demonstrated using a microstrip patch antenna based on a thermistor substrate, and a battery-less radio frequency identification tag. This radio frequency-based sensor readout technique could enable functional materials to be directly integrated in wireless sensing applications.
This paper presents a method to integrate and package an accelerometer within a textile to create an electronic textile (e-textile). The smallest commercially available accelerometer sensor (2 mm × 2 mm × 0.95 mm) is used in the e-textile and is fully integrated within the weave structure of the fabric itself, rendering it invisible to the wearer. The e-textile forms the basis of a wearable woven sleeve which is applied to arm and knee joint bending angle measurement. The integrated e-textile based accelerometer sensor system is used to identify activity type, such as walking or running, and count the total number of steps taken. Performance was verified by comparing measurements of specific elbow joint angles over the range of 0° to 180° with those obtained from a commercial bending sensor from Bend Labs and from a custom-built goniometer. The joint bending angles, measured by all three sensors, show good agreement with an error of less than ~1% of reading which provides a high degree of confidence in the e-textile sensor system. Subsequently, knee joint angles were measured experimentally on three subjects with each being tested three times on each of three activities (walking, running and climbing stairs). This allowed the minimum and maximum knee joint angles for each activity to be determined. This data is then used to identify activity type and perform step counting.
This paper presents the novel use of screen printing and spray coating techniques to fabricate dye sensitized solar cells on textiles for wearable energy harvesting applications. Multiple functional layers of electrodes and active materials have been deposited on everyday use polyester cotton woven fabric and high-temperature resistant glass fiber fabric. The poly cotton fabric limits processing temperatures to 150 °C, while the glass fiber textile can withstand up to 1200 °C. The surface roughness of the textiles has been significantly reduced by screen printing a polyurethane interface layer on the polyester cotton fabric and a liquid polyimide on the glass fiber textile. A silver bottom electrode layer and a bespoke titanium dioxide electron transport layer formulated for each temperature range were then screen printed onto the planarized surfaces. The devices use Iodine/Iodide (I3−/I−) as the liquid electrolyte and were sealed with a plastic PET/ITO, which also forms the counter electrodes. The printed cells have demonstrated photovoltaic (PV) power conversion efficiencies of 3.24% on polyester cotton and 4.04% on glass fiber textiles, in ambient conditions. The polyurethane and polyimide interface layers significantly enhance the performance and stability of the fabricated cells providing extended operational lifetimes. This approach is potentially suitable for the low-cost integration of PV devices into clothing and other textile applications.
11 January 2019 in IEEE Transactions on Components, Packaging and Manufacturing Technology
A novel packaging method that enables the reliable mounting and protection of bare die within a textile yarn has been investigated. The reliability of electronic textiles is highly challenging given the flexibility of the fabric and the rigors of typical applications. Achieving reliable operation requires novel packaging approaches. In order to maximize the reliability and to minimize stresses in the electronic package, the die should be located as close as possible to the central axis of the overall assembly. The die is bonded to a bottom Kapton substrate that contains patterned conductive interconnects and bond pads forming the functional circuit. The circuit is protected by a molded Kapton film that has recesses formed where the die is located. This approach has been compared with three other traditional packaging technologies during washing, twisting, and cyclical bending tests. The novel electronic packaging method shows the best performance in all tests surviving up to 45 wash cycles.
27 December 2017 in IEEE Transactions on Components, Packaging and Manufacturing Technology
A method for packaging integrated circuit silicon die in thin flexible circuits has been investigated that enables circuits to be subsequently integrated within textile yarns. This paper presents an investigation into the required materials and component dimensions in order to maximize the reliability of the packaging method. Two die sizes of 3.5 mm × 8 mm × 0.53 mm and 2 mm × 2 mm × 0.1 mm have been simulated and evaluated experimentally under shear load and during bending. The shear and bending experimental results show good agreement with the simulation results and verify the simulated optimal thickness of the adhesive layer. Three underfill adhesives (EP30AO, EP37-3FLF, and Epo-Tek 301 2fl), three highly flexible adhesives (Loctite 4860, Loctite 480, and Loctite 4902), and three substrates (Kapton, Mylar, and PEEK) have been evaluated, and the optimal thickness of each is found. The Kapton substrate, together with the EP37-3FLF adhesive, was identified as the best materials combination with the optimum underfill and substrate thickness identified as 0.05 mm.